Skip to main content Skip to search Skip to main navigation

Kobalt Solution

Product information "Kobalt Solution"

Kobalt Solution by Betzmann Galvanik  

  

Our cobalt brush plating solution plates up to four times the speed of nickel brush plating solution.

It is very hard (see tech specs) and plates a shade lighter than nickel and darker than chromium.

Kobalt Brush Plating Solution plates a very hard wearing layer that’s a lot harder than nickel and plates at three or four times the speed.

It can be used as a barrier layer, as it slows down the migration of copper into plated gold layers. An alternative barrier layer could be our white bronze or our Palladium Brush, Tank Solution, Nickel Brush or our Nickel Tank Solution.

Cobalt has a slight bluish lustre (although not as pronounced as chromium). Although it is a lot less hypoallergenic than nickel, we do not recommend it for jewellery purposes. 

 

Recommended electrode: Carbon Electrode 4 Volt - Platinum Electrode up to max. 11 Volt.

 

 

Operating Conditions and Deposit Data

Voltage Range 3.5 – 4.5 volts
Temperature 18 – 40 °C
Electrode Carbon, Nickel or Platinum (see notes)
Cobalt content in plate 99.9% (balance carbon)
Plating Rate at (3.5 volts, Carbon Electrode) Approx. 4 micron per minute (spot)
Hardness Above 1,000 MPa (Vickers)
Density of deposit 8.9 g/cm3
Stress Medium – high stress
Special storage requirements None
Shelf life Over 1 year
Health and Safety classification Harmful
Special considerations None
Transport (UN number) None: Not classified as dangerous for transport

 

Notes:

  • We strongly advise against the use of stainless steel anodes for most of our plating processes
  • Plating rates are calculated over a sample area which is permanently covered by swab.
  • Cobalt Plating Solution plates a slightly bluer shade than nickel brush plating solution.

 

 

Labelling acc. to CLP-VO:


Symbol word: Caution! 

H319 Causes severe eye irritation.

P101 If medical advice is needed, have container or label at hand.

P102 Keep out of the reach of children.

P305 IF IN EYES:P351 Rinse cautiously with water for several minutes.

P338 Remove contact lenses if possible. Continue to rinse.

P337 + P313 If eye irritation persists: Get medical advice/attention.

Similar Items

Anode sleeve fuzzy
Anode pad / tampon / anode sleeve / fuzzy sleeve / replacement fabric pad puffy from Betzmann Galvanik.    This puffy fabric pad / anode sleeve or also called tampon is absolutely recommended for all plating processes. Optimally suitable for all coatings and electrolytes.  The coating of larger areas is also quite fast with this pad.   The insertion hole is larger than the electrode and therefore it happens that the moist  anode pad slips off. Therefore, fix the pad on the electrode with a small rubber band.    

€2.38*
Carbon Electrode 6mm
Graphite round rod - Graphite rod anode - Graphite electrode for gold plating.  Graphite electrodes are ultimate for all coatings. The advantage is that in some coatings with stainless steel electrodes, the dislodged metal parts disturb the coating. This does not happen with graphite electrodes, because graphite also filters out contaminated liquids. With bath electroplating, they also need to be replaced occasionally as they slowly dissolve during the plating process.   With pad electroplating, simply loosen the screw on the handle and replace with a new one.   Diameter 6 mm, length approx. 9 cm    Features Used for Doesn’t contaminate Cleaner Activating and electro-cleaning  Its resistive properties help to heat the solution you’re plating with Chromium plating, which needs to be plated at 25 degrees celsius; its natural heating action helps to maintain the solution’s optimal temperature Low cost Can be used for all plating processes but carbon electrodes deteriorate over a period of time and discolour swabs (discolouration does not affect the plating quality)    

€5.90*