Platinum Solution 2 G./Liter
€16.00
Available, delivery time: 1-2 days
Product information "Platinum Solution 2 G./Liter"
Platinum Electrolyte with 2 Gramm Platinum per Liter!
Platinum Bath - Platinizing with Betzmann Electroplating
Platinum is characterized by high abrasion resistance and gives a noble gray surface.
Alternative: White palladium
The platinum bath from Betzmann Galvanik deposits corrosion-resistant, very bright and shiny platinum layers up to a thickness of 0.5 - 1.0 µm.
It is suitable for both decorative and technical applications and is very well suited for pin, bath and pad electroplating!..
Operating data:
Platinum content: 2.0 g/L
pH-value: <1
Density: 1.08 g/ml, increasing
Working conditions:
Voltage: from 3 volts
Bath temperature: 30 - 40 °C
Exposure time: 2 - 4 min.
Anode material: platinized titanium
Anode/cathode surface: 1 : 1
Fabric movement: required
Recommended speed: 2 - 8 cm/sec.
Deposition rate: approx. 11 mg/Amin; approx. 0.5-1.5 A/dm2
Bath movement: recommended
Precipitation data:
Hardness: 500 HV
Layer thickness: max. 1.0 µm
Fineness: 99,9%
Delivery form:
Ready to use 2 g/L Pt
| Features | Applications |
| High concentration of platinum – 2 grams per litre | Suitable for brush plating both decorative and functional items such as jewellery and electrical connectors |
Operating Conditions and Deposit Data
| Voltage Range | 3.0 – 5.0 volts |
| Temperature | 20 – 25 °C (25 °C preferred) |
| Platinum concentration | 2 g/l |
| Electrode | Platinum - Carbon |
| Platinum content in plate | Above 99.9% |
| Plating Rate at (3.5 volts, Platinum electrode) | Approx. 0.25 micron per minute (spot) – see notes) |
| Hardness | 405 Hv |
| Density of deposit | 21.4 g/cm3 |
| Electrical resistivity of deposit | 9.8 micro ohms/cm |
| Stress | Not determined |
| Special storage requirements | None |
| Shelf life | Over 2 years |
| Health and Safety classification | Irritant |
| Special considerations | None |
| Transport (UN number) | 2796 |
Notes:
- We strongly advise against the use of stainless steel anodes for most of our plating processes.
- Higer voltages give greater plating rates, however more gas is liberated and a mist mask is recommended.
- Plating rates are calculated over a sample area which is permanently covered by swab.
- Will plate directly onto freshly prepared nickel or stainless steel.
Hazard statements
H314 Causes severe skin burns and eye damage.
Precautionary statements
P280 Wear protective gloves/protective clothing/eye protection/face protection.
P302 IN CASE OF CONTACT WITH SKIN:
P352 Wash with plenty of water.
P332 If skin irritation occurs:
P313 Get medical advice/attention.
P362 Take off contaminated clothing.
Hazard statements
H314 Causes severe skin burns and eye damage.
Precautionary statements
P280 Wear protective gloves/protective clothing/eye protection/face protection.
P302 IF ON SKIN: P352 Wash with plenty of water.
P332 If skin irritation occurs:
P313 Get medical advice/attention.
P362 Take off contaminated clothing.
HS Code: 38249970
Similar Items
Anode pad / tampon / anode sleeve / fuzzy sleeve / replacement fabric pad puffy from Betzmann Galvanik. This puffy fabric pad / anode sleeve or also called tampon is absolutely recommended for all plating processes. Optimally suitable for all coatings and electrolytes. The coating of larger areas is also quite fast with this pad. The insertion hole is larger than the electrode and therefore it happens that the moist anode pad slips off. Therefore, fix the pad on the electrode with a small rubber band.
Graphite round rod - Graphite rod anode - Graphite electrode for gold plating. Graphite electrodes are ultimate for all coatings. The advantage is that in some coatings with stainless steel electrodes, the dislodged metal parts disturb the coating. This does not happen with graphite electrodes, because graphite also filters out contaminated liquids. With bath electroplating, they also need to be replaced occasionally as they slowly dissolve during the plating process. With pad electroplating, simply loosen the screw on the handle and replace with a new one. Diameter 6 mm, length approx. 9 cm Features Used for Doesn’t contaminate Cleaner Activating and electro-cleaning Its resistive properties help to heat the solution you’re plating with Chromium plating, which needs to be plated at 25 degrees celsius; its natural heating action helps to maintain the solution’s optimal temperature Low cost Can be used for all plating processes but carbon electrodes deteriorate over a period of time and discolour swabs (discolouration does not affect the plating quality)
Platinum electrode from Betzmann-Galvanik: We know that when plating with gold or silver, you want to achieve only the best results and this is achieved by using our platinum electrode (platinized titanium). This will more than meet your requirements. It hardly wears out and leaves no black spots or stains when plating. For top quality gold plating, we recommend the use of this electrode. Care should be taken to clean the electrode carefully after each use! Properties "Platinum Electrode 6 mm Platinum electrode (platinized titanium with a platinum layer of 2.5 µm platinum) Ø 6 mm x 100 mm Standard electrode for experiments in electrochemistry (electroplating, electrolysis, ion migration, determination of electrochemical potentials, etc.) Spare platinum electrode for Hofmann decomposition apparatus, electrolyzer Platinum-coated titanium anodes are among the classic anode materials for electroplating because they combine the excellent electrochemical properties of platinum with the good corrosion properties of titanium. They are characterized by a long service life at high current density and are versatile in use. They are equally suitable for platinum and ruthenium baths, for hard chrome plating, as bright rhodium baths and for cathodic corrosion protection. The standard platinum layer thickness is 2.5 μm. In order to achieve the best results when plating with gold (adhesive gold bath, bright gold plating bath) or silver, they are indispensable. This platinum electrode will more than meet your requirements, it hardly wears out and leaves no black spots or stains when plating. For top quality gold plating, I recommend using this electrode. Other possible applications: Water electrolysis/separation of hydrogen and oxygen, water disinfection, production of chlorates (chlorate synthesis) and perchlorates. Recommended operating data: Operating voltage from 3 volts distance anode/workpiece surface 5 cm anodic current intensity (specific current density) max. 75 A/dm² (7.5 mA/mm² = 750 mA/cm²), i.e. a multiple of the values typical in electroplating (0.5 ... 5 A/dm²) pH value: 0 - 11 Bath temperature max. 60 °C