Skip to main content Skip to search Skip to main navigation

Rosegold Mixer

Product information "Rosegold Mixer"

Rosegold Mixer - Betzmann Galvanoshop:

Simply add Rose Gold Mixer to K-Gold to plate fabulously warm, lustrous tones of rose gold.
All you need to do is mix the two together to create just the right amount of solution you need.

We recommend you buy the mixing kit to make sure you measure out the correct ratios.
A 1:10 mix will give you a darker shade of rose gold commonly used for eastern European jewellery,
while a mix of 2:10 gives a mix not too dissimilar to highly polished pure copper, however this one does not tarnish.


If plating on to stainless steel, nickel or its alloys, first plate a layer of 24 carat gold or Goldflash to

give a good, solid base on which to plate your Rose Gold layer.

 

Features Used for
Rose gold plate is very hard compared to pure gold. Great for plating items subject to a high-wear environment (jewellery).
Plates fast. Reduces plating time.
When mixed with K-Gold, creates the classic warm tones of rose gold. Selective plating of a range of personal items for example jewellery and watch cases and straps. Can be used on larger items such as silverware and picture frames.
Redder deposits can be obtained by increasing the volume of mixer. Greater flexibility in colour matching.
Consistency of alloy throughout process sequence. Very useful especially when plating large work or plating to higher thickness: the shade of gold plated doesn’t change.

 

Instructions for use

Carbon Electrode
3 – 3.5 volts
20 – 25 centigrade

Ratio of Rosegold Mixer to K-Gold Shade Produced   Remarks
1:10 Yellow-red shade   18 carat alloy (75% gold, 25% copper). Plates fast (up to 1.5 microns per minute). Bright, hard gloss finish.
1.5:10 (see note below)
Becomes redder   15 carat gold alloy (62.5% gold, 37.5% copper) Plates bright and fast.
2:10 (see note below)
Red gold   12 carat alloy – (50% gold, 50% copper). If wanting to plate over 0.25 microns, plate until it goes dull, polish with MPU and then plate again.
4:10 (see note below)
Red gold   Below 10 carat alloy. Tarnishes readilly and not recommended for decorative purposes.

Notes:

  • Rose gold mixes above 1:10 are a lot more susceptible to tarnish than mixes of 1:10 and lower
  • Remove any existing layers of rose gold before plating

 

 Labeling gem. CLP-VO:

 GHS07

Signal word: Caution 

H315 Causes skin irritation

H319 Causes severe eye irritation.

H335 May cause respiratory irritation.

P261 Avoid breathing dust/fume/gas/mist/vapor/aerosol.

P280: Wear protective gloves/protective clothing/eye protection/face protection.

P305 IF IN EYES:P351 Rinse cautiously with water for several minutes.

P338 Remove any contact lenses if possible. Continue to rinse.

 
 
 

 

Similar Items

K-Gold - Clear Gold 10 Gramm/L.
  Product information "Klargold - Clear Gold " by Betzmann Galvanik Clear gold with 10 grams of gold per liter is just like the gold flash - wonderfully suitable as an intermediate layer or decorative layer.    Betzmann Galvanik's Clear Gold has the following main applications:   1. for mixing with Rose Gold Mixer - White Gold Mixer - Green Gold Mixer or Goldweisser. The hardness additives are in the respective mixer liquids. You can find the instructions in the respective item description and guide.   2. Optical-decorative layer: Gold is soft and requires the addition of cobalt as a hard abrasion resistant top layer, which is not included in this product. Therefore, the gold layer from the Clear Gold appears slightly lighter yellow. Parts that are not subject to stress, such as souvenirs, horseshoes for decoration, etc., can be easily, directly and inexpensively gilded with the Clear Gold.   Tip: You can first very intensively and thickly gild parts with the clear gold, because the high proportion of gold very quickly and thick gold layers and then coated briefly with the 8 or 12 grams cobalt-displaced hard gold!   3. bonding primer for the following coatings: Many applications require thin layers of gold before actual plating.  With the Clear Gold from Betzmann Galvanik you can apply the desired gold layer. As an example, direct silver plating of nickel is usually not feasible, so you can first gold plate with the Clear Gold, then silver plate. Likewise, when using black chrome, rose gold plating, green gold plating, the clear gold serves as an optimal bonding base when copper or nickel cannot be applied directly! Also, the gilding of nickel, which naturally oxidizes, is very easy and spotless possible. Then chrome plating on clear gold can be done even easier and without problems.   Recommended electrode: platinum electrode, graphite electrode Voltage: from approx. 4 volts  Cyanide free   Procedure: Polishing if necessary Degreasing Activate Clear Gold Continue with the top coat chrome, white gold, rose gold, green gold   Features Used for Designed mainly as a base solution for mixing with our Coloured Gold Mixers Mixing with Yellow, White, Rose, and Green Gold Mixers and Brass Effect Gold Mixer. Can be mixed with 2 or more Gold Mixers Creating a huge spectrum of different shades and tints of gold – good for exactly matching colour of original gold plated layer Can be plated on its own, forming a soft, 24 carat gold layer, completely cyanide free Mainly functional purposes only. Needs a Gold Flash undercoat if plating on to stainless steel     Signalword: Warning   H-phrases: H332 Harmful by inhalation. H312 Harmful in contact with skin. H302 Harmful if swallowed. P phrases: P280 Wear protective gloves/protective clothing/eye protection/face protection. P301 IF INFECTED:P310 Immediately call a POISON CENTER/doctor/  

Content: 0.05 Liter (€1,280.00* / 1 Liter)

From €64.00*
Carbon Electrode 6mm
Graphite round rod - Graphite rod anode - Graphite electrode for gold plating.  Graphite electrodes are ultimate for all coatings. The advantage is that in some coatings with stainless steel electrodes, the dislodged metal parts disturb the coating. This does not happen with graphite electrodes, because graphite also filters out contaminated liquids. With bath electroplating, they also need to be replaced occasionally as they slowly dissolve during the plating process.   With pad electroplating, simply loosen the screw on the handle and replace with a new one.   Diameter 6 mm, length approx. 9 cm    Features Used for Doesn’t contaminate Cleaner Activating and electro-cleaning  Its resistive properties help to heat the solution you’re plating with Chromium plating, which needs to be plated at 25 degrees celsius; its natural heating action helps to maintain the solution’s optimal temperature Low cost Can be used for all plating processes but carbon electrodes deteriorate over a period of time and discolour swabs (discolouration does not affect the plating quality)    

€6.00*
Mixer set for measuring
Mixer set for measuring Real Gold Betzmann    With this mixer set consisting of 1x measuring cylinder, 2x pipette, 2 x beaker you can mix rose gold, white gold, green gold, etc. in the right proportion exactly.

€14.50*