Rust Remover

Nickel stripper strips nickel plating from steel, copper, brass and silver easily and delivers the following pluses; Ready-to-use solution: no need for mixing Low hazzard Stripping rates of up to 50 microns per hour at 62 °C High capacity (1 litre can strip 40 grams of nickel) Low odour: minimum ventilation needed Supplied as a one-component, ready-to-use solution Non-electrolytic stripper: no need for a separate rectifier Long bath life Can be shipped worldwide Operating Conditions Temperature Range 50 -65 °C (see notes) Tank Glass (see notes below), steel or polypropylene Agitation Mechanical (stirrer). Never use air agitation Stripping rate See notes below Stripping capacity Can strip up to 40 grams of nickel per litre Special storage requirements None Shelf life 1 – 2 years Health and Safety classification Irritant Special considerations None Transport (UN number) None: Not classified as dangerous for transport   Notes: Tanks should be made of stainless steel, polypropylene or glass. If using glass,return the solution (cooled) to the container after use. Heating should be provided by a Teflon-coated stirring bar (if stripping in a beaker). For larger installations, stainless steel or titanium-sheaved heaters should be used. Stripping rates can be almost doubled by using light mechanical agitation: Stripping rate at 50°C = 10  microns per hour (no agitation) Stripping rate at 50°C = 17  microns per hour (with agitation) Stripping rate at 62°C = 50 microns per hour (with agitation) Black smut remaining can be removed by ultrasonic cleaning or scouring with pad. 

Galvanic Nickel Electrolyte from Betzmann Galvanik for self-nickel plating Nickel Plating Solution   Our absolutely high-quality galvanic nickel electrolyte has been specially developed for self-nickel plating and may be sold to private individuals without an end-use declaration.   Depending on the material of the workpiece as well as the detailed procedure of nickel plating you will achieve the following results: reliable corrosion protection by a layer combination such as copper-nickel chemically resistant protective layer against diluted acids, alkalis as well as air and water diffusion protection for subsequent electroplating (e.g. diffusion from a base copper layer into the covering gold layer) decorative protective coating with a high-gloss surface, which also serves as wear protection. As an electroplating nickel electrolyte, our product is suitable for bath electroplating as well as for pin electroplating and pad electroplating. During nickel plating, the magnetic properties of the workpiece are retained and it exhibits a high-gloss silver-like color with a subtle yellow tint. Just as convincing as the final result is the high deposition rate exhibited by the nickel electrolyte. Electroplated nickel - decorative or protective coating   If a simply formed workpiece or component is to be provided with a protective layer, we recommend the combination of copper and nickel. In this way, you immediately achieve reliable corrosion protection, which you would otherwise only achieve with pure nickel plating with a layer thickness of 25 to 50 µm. Only at these thicknesses does the coating have the required freedom from pores, since nickel electrolytes always deposit with fine pores. However, electroplated nickel not only protects against corrosion. The coating, which is uncomplicated to apply, is highly resistant to dilute acids and alkalis and serves as wear protection. If several electroplating steps with layers of different metals are planned, an electroplated nickel electrolyte can be used as a barrier layer. In this way, you prevent diffusion or color mixing of different layers. In all processes, it is irrelevant whether you use our nickel electrolyte for bath electroplating or for pin electroplating and pad electroplating. For decorative plating, the combination of bright nickel and chrome is ideal for reliably achieving flat surfaces, although pure bright nickel plating may be sufficient depending on the application.   Application instructions for Betzmann Galvanik's Free Nickel Nickel Electrolyte (bright nickel) Our high-performance Free Nickel Nickel Electrolyte is preferably processed at room temperature (range from 15 to 60 °C). It is suitable for all common metals, semi-precious and precious metals with the exception of aluminum, chrome (dechrome beforehand) and titanium.   If you plan to nickel plate stainless steel yourself, please be sure to use a nickel strike for pretreatment or gold plate in advance with Goldflash. to increase adhesion.   Before galvanic nickel plating, clean the workpiece particularly thoroughly. Remove rust completely and degrease the component, e.g. with isopropanol. Be sure to work with clean disposable gloves to avoid transferring skin grease to the workpiece.   The nickel electrode from Betzmann Galvanik is particularly recommended - this results in a very high range, as the nickel is permanently enriched.   Please pay attention to the following recommendations, depending on the electroplating method used. Parameters: Bath electroplating: 2-5V (approx. 3V recommended at 10cm distance) Pin electroplating: 6-12V (approx. 8-9V recommended) Current density: 0.3-1.2A/dm² (up to 3A/dm² with bath movement) Working temperature: 15-60°C pH value: approx. 4 (can be corrected e.g. with 10% sulphuric acid) Deposition speed: approx. 0.3µm/min at 1A/dm² and 20°C   Identification of the mixture: Signal word: Caution Free nickel (contains nickel sulfate, nickel dichloride, nickel bis(sulfamidate), nickel di(acetate), diammonium nickel bis(sulfate)) GHS07 H317 May cause an allergic skin reaction. H412 Harmful to aquatic life with long lasting effects. P102 Keep out of the reach of children. P103 Read all instructions carefully and follow them. P261 Avoid breathing dust/vapor/aerosol. P280 Wear protective gloves and eye/face protection. P302+P352 IF ON SKIN: Wash with plenty of water. P333+P313 If skin irritation or rash occurs: Get medical advice/attention. P501 Do not dispose of contents/container with household waste and dispose of in accordance with regional/national regulations.        

PRODUCT PRESENTATION - HIGH SPEED GOLD ELEKTRTOLYT 999 FINE GOLD - 23,8 CARAT  WITH 12 GRAMS OF GOLD PER LITER   More gold in the electrolyte means even faster plating, thicker layers with the same working time or more surface area. Also the purchase of the high speed gold is cheaper, because you buy more gold per liter at a lower price. Do-it-yourself gold plating has never been easier. Our gold electrolyte from Betzmann Galvanik can be purchased by anyone. So whether it is for use in the highly professional use of laboratories, industry, luxury companies, to the use in the hobby, main or in the side business, companies, schools, universities, TH , IHK or other authorities. With this extremely fast and very hard depositing gold electrolyte from Betzmann Galvanik, you can usually coat the following metals directly: Stainless steel of all kinds, surgical steel, copper, silver, brass, nickel, iron, steel,   The pink color of the electrolyte is the hardness additive cobalt. This gives the otherwise much too soft gold an abrasion resistant surface. This is not toxic in the admixed composition.  The gold electrolyte from Betzmann Galvanik is anti-allergenic, was extracted from crisis- and conflict-free gold and is food-safe.  Our Betzmann Galvanik Gold Electrolyte has a very fast deposition and further achieves a very hard gold layer. It has a very good covering effect and is therefore one of the best products on the market worldwide. A special preservative results in a very long shelf life of at least 2 years and prevents sedimentation, which occurs with many other gold electrolytes. The Gold Electrolyte from Betzmann Galvanik can be used for pen electroplating, pad electroplating and also for bath electroplating!  The Gold Electrolyte from Betzmann Galvanik is used worldwide, e.g. for the gold plating of boat parts made of brass that are exposed to salt water, medical technology, measurement technology, for optical gold plating, for technical gold plating, gold plating of drive shafts, musical instruments and their parts, both inside and outside, body jewelry, intimate protection, dental jewelry, dental technology, drills of all kinds, shisa, e-cigarettes so-called. Vaporizers, vehicle parts, engine parts, motorcycle parts, airplane interiors, exhaust systems and manifolds, as gold is very heat resistant, sporting goods, diving equipment, keys and pendants, jewelry, chains and rings of all kinds, piston rods, pipes, table feet, bathroom fixtures and many more. Partial coatings are possible by masking and masking surrounding areas. To avoid material loss when coating sloping surfaces, we recommend our thickener/gel former. With this you can thicken all electrolytes also chrome remover, cleaner etc..     Also you can use with this gold mostly in the ratio 1:10 our mixer products like rose gold, white gold and green gold! Optimal results are achieved with the platinum electrode 6mm - 10cm long or the flat platinum electrode, since platinum electrodes can build up very thick layers far above 10 microns and more. Graphite electrodes can also be used.  Gold content: 12 grams per liter    The procedure for gold plating: It is recommended to polish the surface to a shine first - the nicer the surface, the nicer the shine will be Thorough degreasing with the electrocleaner Activate the surface with the activator Gilding with platinum electrode starting around 5 volts    Operating Conditions and Deposit DataVoltage Range3.0 – 4.5 voltsTemperature14 – 25 °CGold Concentration12g/lElectrodePlatinum or Carbon (see notes)Gold content in plate99.9% (balance carbon)Plating Rate at (3.5 volts, Platinum electrode)Approx. 0.8 micron per minute (spot)Hardness220 – 230 HvDensity of deposit19.3 g/cm3StressMedium stressSpecial storage requirementsAway from sunlightShelf life3 – 6 monthsHealth and Safety classificationHarmfulSpecial considerationsContains potassium cyanide (0.3%)Transport (UN number)None: Not classified as dangerous for transport Notes:We strongly advise against the use of stainless steel anodes for most of our plating processesPlating rates are calculated over a sample area which is permanently covered by swab.

The metal care product is used for cleaning and polishing surfaces.    With the metal care almost all types of surfaces (except textiles) can be cleaned, treated and sealed with little effort and completely without water! Metal Care from Betzmann Galvanik does not contain acids or alkalis. It is ph-neutral and slowly biodegradable. It is even machine applicable by means of an eccentric polishing machine.      Some examples of use:  Car, boat, motorcycle, bicycle, kitchen, bathroom, ceramics, glass, leather, imitation leather, amarture board, plastic, camper, stainless steel, chrome, glass panes, TV, monitors, glasses, helmets, tiles, mirrors, shoe sole sides,  cell phone displays, store counters, high-gloss fronts, foiling (matt/glossy), advertising and company signs, solar systems, solariums, whirlpools, pools, rims, ovens, acrylic glass, ceramic hobs, CNC machines, chrome fixtures in the bathroom and much more.      Application:  Shake bottle briefly before use. Apply the metal care to the object to be treated and distribute/massage.  Then polish or wipe the lotion away with a clean microfiber cloth.  It can be applied by hand or by machine. For machine application, the care product can be used like a normal polish. For this purpose, apply the agent to the machine polishing attachment and process with gentle pressure. Then polish or wipe off the lotion with a clean microfiber cloth. or wipe clean. Due to its additional cleaning function, the metal care replaces a large number of polishes for automotive reconditioners. Smooth surfaces appear  after the application in their original shine and are sealed (Lotus effect). Dull lacquers are beautifully matt again after application and dirt and grease residues are grease residues are removed. Glass panes become streak-free clean after application and less susceptible to soiling (sealed).  With each new or further application, the protective film/sealing is further built up and the pores in the surface are closed. The product does not contain chalk or wax ingredients like common polishes. Thus also plastics can be polished effortlessly and appear again in the old shine (no white stripes or residues on plastic). The sealing usually lasts between 2-8 weeks (depending on the area of application and stress on the polished object). object).    Notice:  The product should not necessarily be used in the blazing sun, otherwise it may happen that you have to work harder to polish up the product One should also not use the metal care on smooth floors, as this surface then becomes even smoother and possible slipping danger exists.  

PRODUCT PRESENTATION - GOLD ELECTROLYTE 999 FINE GOLD - 23,8 CARAT  WITH 2 GRAMS OF GOLD PER LITER   Do-it-yourself gold plating has never been so easy. Our Gold Electrolyte from Betzmann Galvanik can be purchased by anyone. So whether it is for use in the highly professional use of laboratories, industry, luxury companies, to the use in the hobby, main or in the side business, companies, schools, universities, TH , IHK or other authorities. With this extremely fast and very hard depositing gold electrolyte from Betzmann Galvanik, you can usually coat the following metals directly: Stainless steel of all kinds, surgical steel, copper, silver, brass, nickel, iron, steel,   The pink color of the electrolyte is the hardness additive cobalt. This gives the otherwise much too soft gold an abrasion resistant surface. This is not toxic in the admixed composition.  The gold electrolyte from Betzmann Galvanik is anti-allergenic, was extracted from crisis- and conflict-free gold and is food-safe.  Our Betzmann Galvanik Gold Electrolyte has a very fast deposition and further achieves a very hard gold layer. It has a very good covering effect and is therefore one of the best products on the market worldwide. A special preservative results in a very long shelf life of at least 2 years and prevents sedimentation, which occurs with many other gold electrolytes. The Gold Electrolyte from Betzmann Galvanik can be used for pen electroplating, pad electroplating and also for bath electroplating!  The Gold Electrolyte from Betzmann Galvanik is used worldwide, e.g. for the gold plating of boat parts made of brass that are exposed to salt water, medical technology, measurement technology, for optical gold plating, for technical gold plating, gold plating of drive shafts, musical instruments and their parts, both inside and outside, body jewelry, intimate protection, dental jewelry, dental technology, drills of all kinds, shisa, e-cigarettes so-called. Vaporizers, vehicle parts, engine parts, motorcycle parts, airplane interiors, exhaust systems and manifolds, as gold is very heat resistant, sporting goods, diving equipment, keys and pendants, jewelry, chains and rings of all kinds, piston rods, pipes, table feet, bathroom fixtures and many more. Partial coatings are possible by masking and masking surrounding areas. To avoid material loss when coating sloping surfaces, we recommend our thickener/gel former. With this you can thicken all electrolytes also chrome remover, cleaner etc..   Also you can use with this gold mostly in the ratio 1:10 our mixer products like rose gold, white gold and green gold! Optimal results are achieved with the platinum electrode 6mm - 10cm long or the flat platinum electrode, since platinum electrodes can build up very thick layers far above 10 microns and more. Graphite electrodes can also be used.  Gold content: 2 grams per liter    The procedure for gold plating: It is recommended to polish the surface to a shine first - the nicer the surface, the nicer the shine will be Thorough degreasing with the electrocleaner Activate the surface with the activator Gilding with platinum electrode starting around 5 volts   Operating Conditions and Deposit Data Plating Factor 0.01 A/cm2 Plating rate 0.12 micron per minute at 0.01A/cm2 Temperature 18 – 25 °C pH 4.4 – 5.0 Gold concentration 2 grams per litre Agitation very low (Stirring Bar Mini) Electrode Mesh Gold content in plate 99.9% (balance carbon) Cathode efficiency ~25% at Plating Factor = 0.01A/cm2 Hardness 190 – 210 Hv Density of deposit 19.3 g/cm3 Stress Medium Special storage requirements Away from sunlight Shelf life 1 – 2 years Health and Safety classification Harmful             Signalword: Warning  H-phrases: H332 Harmful by inhalation. H312 Harmful in contact with skin. H302 Harmful if swallowed. EUH032 Contact with acids liberates very toxic gas. P phrases: P280 Wear protective gloves/protective clothing/eye protection/face protection. P301 IF INSPECTED:P310 Immediately call a POISON CENTER/doctor.  

Electrocleaner - degreaser from Real Gold Betzmann:   We have put a lot of research and development work into this product to ensure that it enables completely safe and harmless work, thoroughly cleans and degreases conductive material and does not attack other substances such as varnish or paint.    Using electricity, from 8 volts, it removes the most stubborn residues of dirt and reduces the oxide layers of metals before activation. This product can be used on all substrates. The Cleaner cleans effortlessly tarnished Silver and also removes oxide layers from copper and brass.   Please note: Our Elektrocleaner does not contain caustic soda - sodium hydroxide - which is corrosive and dangerous too.   Betzmann Galvanic Degreaser - our all-round degreasing agent for cleaning metals and all metal surfaces   For perfect and shiny surface coating it is essential to remove residues from the workpiece, to free fats and oxides. Adhering grease residues or fingerprints can quickly lead to unsightly results.  With the help of the extraordinary formula of the degreaser you can quickly and easily remove greasy dirt such as lubricants, Remove oil or silicone residues. Briefly brushing or dipping your work piece into the degreasing agent will optimal preparation for the subsequent coating. In this way you can successfully electroplate and coat yourself.      Regulation (EC) No. 1272/2008 Signal word: Warning H319 Causes serious eye irritation. Hazard statements P280 Wear protective gloves/protective clothing/eye protection/face protection. P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove any contact lenses if possible. Continue rinsing. P337+P313 If eye irritation persists: Get medical advice/attention.  

Metal Polish Ultra from Betzmann Galvanikis a liquid cleaning and care emulsion for all metal surfaces. The high-quality polishing agents ensure intensive yet gentle cleaning of weathered surfaces and remove stubborn dirt. Gives aged surfaces a new shine. Easy to apply and polish. The product is ideal for large areas.