Alkaline Copper Electrolyte BMG-093 Alkaline copper electrolyte for electroplating metal surfaces Short Description The Alkaline Copper Electrolyte BMG-093 is a ready-to-use alkaline (basic) solution for electroplating copper onto metal parts. Unlike acidic copper electrolytes, this alkaline copper bath is especially suitable for acid-sensitive materials such as iron, steel, or zinc. It is easy to use and produces smooth, uniform copper layers that can serve either as a protective coating or as an intermediate layer for further electroplating processes such as nickel or chromium plating. What is this alkaline copper electrolyte used for? The alkaline copper electrolyte is used to electroplate metal surfaces with a copper layer in order to: protect metal parts against corrosion create a smooth and even copper surface provide an ideal base layer for further coatings (nickel, chromium, precious metals) allow copper plating on acid-sensitive metals such as steel, iron, or zinc Typical applications include: restoration and repair work corrosion protection of steel and iron parts preparation for multi-layer electroplating systems hobby, craft, and small-scale professional projects How does copper plating work? (simple explanation) In electroplating, copper is transferred onto a workpiece using electrical current: The workpiece is thoroughly cleaned and degreased It is connected as the cathode (negative pole) A suitable anode (e.g. copper sheet or copper wire) is connected as the positive pole When direct current is applied, copper ions from the electrolyte are deposited evenly onto the surface The result is a thin, uniform copper coating with a characteristic reddish metallic appearance. Advantages of Alkaline Copper Electrolyte BMG-093 suitable for acid-sensitive metals easy to use, also suitable for beginners produces uniform and decorative copper coatings ideal as a base layer for nickel or chromium plating suitable for tank plating, brush plating, and pen plating cyanide-free and easy to handle proven electrolyte from professional electroplating technology Technical Parameters PropertyValue / RangeNotesElectrolyte typeAlkaline copper electrolytebasic, cyanide-freepH valueapprox. 8–9alkaline rangeOperating temperature20–60 °Croom temperature to slightly heatedVoltage (tank plating)approx. 1–2.5 Vrecommended from ~1.5 VVoltage (brush / pen plating)approx. 2.5–6 Vrecommended ~4–5 VCurrent densityapprox. 0.2–1.5 A/dm²up to ~3 A/dm² with agitationDeposition rateapprox. 0.4 µm/min at 1 A/dm²typical plating rateAnode materialCopper (preferred), nickel, or suitable inert anodescopper recommendedSuitable substratesSteel, iron, zinc and other metalsideal for acid-sensitive materialsNot suitable forAluminum, chromium, titanium (without special pretreatment)testing recommended (Values represent typical operating parameters for alkaline copper electrolytes.) Practical Application Notes Surface preparation is critical: remove grease, oil, oxides, and rust before plating Copper anodes help maintain a stable copper concentration in the bath Gentle bath movement improves coating uniformity Copper layers are an excellent base for subsequent nickel or chromium plating Safety Information Although this alkaline copper electrolyte is cyanide-free, it is still a chemical product: Wear chemical-resistant gloves and safety goggles Avoid contact with skin and eyes Use only in well-ventilated areas Do not inhale vapors or aerosols Keep out of reach of children and unauthorized persons Scope of Delivery Alkaline Copper Electrolyte BMG-093 Quantity according to selection Important Notice This product requires basic knowledge of electroplating. For optimal results, we recommend using suitable pre-treatment and post-treatment products from our range.

Conductive silver lacquer spray 150 ml from Betzmann Galvanik    Product information about Betzmann electroplating silver conductive lacquer spray (150 ml)   Item description: Betzmann Galvanik conductive silver lacquer spray (150 ml) - the product properties at a glance:   highly conductive easy to spray on 16 grams of silver and minimal copper content, hence the red tinge suitable for bath and pen plating With conductive silver lacquer from Betzmann Galvanik you can make non-conductive surfaces such as plastic, wood and many more conductive and then simply electroplate them, for example. After application, the conductive lacquer can be electroplated with either pen plating or bath plating. In order to achieve glossy results, the object treated with the conductive lacquer should be coated with the acid copper electrolyte or our new PP copper - you can then polish to a shine and then further silver or gold plating.   Please read our operating instructions carefully before using the conductive lacquer spray.   Scope of delivery: 150 ml silver conductive lacquer spray   SILVER CONDUCTIVE PAINT SPRAY Fields of application:   Conductive treatment of plastics, glass, ceramics and many other materials. Also very well suited as a decorative lacquer for flowers - also preserves fresh flowers without drying them first.       General use:   Apply a thin layer of conductive lacquer to the pre-cleaned, grease-free surface. Plastic parts can be coated better if they are sprayed with plastic primer beforehand. Spray the conductive lacquer in several layers in cross-coats. Allow the conductive lacquer to dry thoroughly before each spraying cycle (5 - 15 minutes). In order to remove last solvent residues it is recommended to blow-dry the conductive lacquer thoroughly with a hair dryer before electroplating. The conductive lacquer should be shaken thoroughly before spraying to prevent clumping.       Pen plating:   Small areas can be plated with pen plating directly after drying. However, care should be taken to apply only weak pressure to the lacquer to avoid scratches. The object with the minus pole should only be contacted but not clamped. Here, our copper plates are suitable.   The first layer that is applied must be bright copper or PP copper, as this electrolyte quickly separates and strengthens the conductive lacquer layer. Afterwards, further coatings can be applied with other electrolytes. Since the conductive lacquer can easily be damaged, pen plating on conductive lacquer is only recommended to a limited extent. It is much better to coat the object with bright copper electrolyte beforehand.       Bath electroplating:   The best results can be achieved with conductive lacquer if it is copper-plated after spraying. The coating should be thick enough to obtain a polish-resistant layer (copper plating in bath for about 30 - 45 minutes). Before applying further coatings, the copper can then be carefully polished to a shine. It is important to spray especially edges and transitions carefully, as the conductive lacquer is most sensitive at these points and tends to run off.   Safety Instructions:   The conductive lacquer is inflammable and dangerous to the environment. Therefore keep the conductive lacquer away from ignition sources and sparking. Avoid electrostatic charging. Do not allow the conductive lacquer to get into the waste water and dispose of dried residues in hazardous waste.     

Copper Conductive Paint BMG-058-K.2 Electrically conductive copper paint for repair, conductivity improvement and contact paths Short Description The Copper Conductive Paint BMG-058-K.2 is a ready-to-use, electrically conductive coating and repair paint based on copper. It is designed for spot or area repair of conductive paths, electrification of surfaces, and filling small breaks in conductors, as well as for creating electrically conductive layers on non-metal parts. The paint delivers good conductivity, adheres reliably to many substrates, and can be used in a wide range of electronics, fine mechanics, and industrial applications. Applications The copper conductive paint is used for: Repair and restoration of conductor tracks on PCBs, contacts and circuits Creating conductive connections on non-metallic supports Filling small discontinuities in conductive elements and contact points Improving electrical transitions during assembly or repair Prototyping and fine wiring in electronic and electrical projects It is suitable for workshop, hobby, and professional repair and assembly tasks. How It Works (Simple Explanation) Conductive paint contains finely dispersed copper particles. After application and drying, the paint forms an electrically conductive layer as the copper particles connect within the film: Prepare the surface: Clean and degrease the area. Apply the paint: Use a brush, applicator, or fine needle to apply. Dry / Cure: The paint dries and becomes electrically conductive. Post-work: Mechanically refine or electroplate over the conductive layer if needed. Benefits of Copper Conductive Paint BMG-058-K.2 Electrically conductive coating immediately after drying Good adhesion on metal, plastic, and ceramics Easy to apply with basic tools Repair-friendly for conductive paths and contacts Versatile use in electronics, sensors, and fine mechanical assemblies Can serve as a pre-layer for electroplating Technical Parameters (Guidelines) PropertyValue / RangeProduct typeElectrically conductive copper paintCompositionCopper-filled coating systemConductivityElectrically conductiveDryingAir dry or gentle heating to accelerateAdhesionGood on metal, plastic, ceramicApplicationBrush, applicator, precision tipLayer thicknessSeveral micrometers (µm), application-dependentCuringAmbient conditions, relative humidity relevant Practical Application Tips Preparation: Clean and degrease thoroughly. Application: Apply the paint in thin layers to the desired area. For higher conductivity, apply multiple thin layers. Drying: Allow to dry at room temperature; gentle heating can speed curing. Aftercare: Once fully dry, the layer can be mechanically worked on or plated over. Safety Information Conductive paints contain chemical solvents and must be handled safely: Wear protective gloves and eye protection Avoid contact with skin and eyes Work in a well-ventilated area Do not ingest; keep out of reach of children Avoid eating, drinking or smoking while working Dispose of according to local chemical waste regulations Conclusion The Copper Conductive Paint BMG-058-K.2 is a practical and electrically conductive coating and repair solution. It is ideal for creating and repairing conductive paths, improving connectivity, and as a foundation for further plating steps. With simple application, reliable adhesion, and good conductivity, it is suited for workshops, professionals and electronics enthusiasts alike.

Copper Plate Electrode (SW10051M) Short Description The Copper Plate Electrode is a large‑area sacrificial anode made from high‑purity copper (≥ 99.9 %) designed for electroplating. It provides a consistent supply of copper ions to the electrolyte, promoting stable baths, uniform deposits and improved conductivity in copper plating applications.  Product Description This plate is manufactured from pure copper, which dissolves evenly into the electrolyte to maintain a consistent metal ion concentration. The flat, broad surface makes it ideal for covering larger workpieces or for use in plating tanks where even current distribution is critical to achieving high‑quality copper coatings. Copper anodes like this plate are typically used in bath electroplating settings and can also serve as a foundation layer before other coatings such as nickel or chrome are applied. Typical Applications Electroplating of copper on metal substrates Bath plating for decorative or functional copper layers Undercoat / intermediate layer before nickel or chrome plating Workshop, lab and production electroplating Applications involving larger workpieces requiring extensive coverage  Key Benefits High copper purity (≥ 99.9 %): clean ion release for consistent baths Broad plate design: promotes uniform current distribution Improved deposit quality: even, durable copper coatings Flexible use: suitable for a range of plating setups Easy integration: fits naturally into standard bath electroplating processes  Usage Instructions Preparation: Thoroughly clean and degrease all workpieces prior to plating. Placement: Position the copper plate electrode as the anode (positive terminal) in the electrolyte. Connect: Attach the electrode to the positive output of your power supply and the workpiece to the negative (cathode). Plating: Adjust voltage and current according to the specific copper electrolyte used. Maintenance: Periodically clean off any buildup to maintain performance and longevity. Conclusion The Copper Plate Electrode is a reliable, versatile accessory for copper electroplating, offering consistent performance and uniform deposition thanks to its large active surface and high material purity — suitable for hobbyists, workshop use and professional electroplating environments alike.

Copper Electrode Ø 6 mm (BMG-011) Short Description The Copper Electrode Ø 6 mm is a high-purity copper anode (99.9 %) designed for efficient electroplating of copper. It delivers consistent copper ion supply in the electrolyte, enabling fast, even and high-quality copper plating — suitable for bath, pen and pad plating applications. Product Description Made from pure copper (99.9 %), this electrode offers excellent electrical conductivity and controlled copper release into the plating bath. This helps maintain a stable metal content in the electrolyte, improving deposit quality and process reliability while reducing waste and costs. Typical Applications Copper electroplating in various electrochemical setups Bath, pen and pad plating techniques Decorative and functional copper coatings Foundation layers for corrosion protection before further plating Use in workshops, labs and production environments Key Benefits Superior conductivity: ensures stable current flow during plating.  High-purity copper: reduces bath contamination and supports consistent results.  Faster copper ion exchange: improves plating efficiency and finish quality.  Cost savings: can reduce plating solution expenses by up to 40 %–50 % by maintaining bath metal content.  Easy handling: fits standard electrode holders and plating fixtures. Usage Tips Preparation: Thoroughly clean and degrease workpieces before plating. Plating Setup: Connect the electrode to the positive terminal while the workpiece serves as the cathode. Maintenance: Clean the electrode periodically to maintain performance. Compatibility: Best used with copper plating electrolytes in both alkaline and acidic baths. Conclusion The Copper Electrode Ø 6 mm is an essential component for efficient and reliable copper electroplating, offering a balanced combination of performance, cost-effectiveness and ease of use for hobbyists, technicians and professional plaquers alike.

  Silver conductive lacquer (12 grams or 50 grams contains 50% pure silver powder) ready conductive lacquer for application - also suitable for airbrush    For the coating of non-conductive materials such as wood, glass, plastic, this conductive silver lacquer can be used by Betzmann electroplating can be a helpful support.  It should be noted that you must prepare the substrate perfectly so that the paint adheres there optimally. After drying, it will provide a conductive surface and can be coated. Children's shoes, flowers, etc. can thus be coated.  You can apply it with a brush or also with an airbrush gun. The smoother and shinier the paint layer, the higher the degree of gloss of the coating - please use very long and thick acid or copperplate with PP-copper. This brings the gloss!   Conductive silver lacquer, conductive silver - contains 50 % pure silver powder in acrylic lacquer (water-based) The Betzmann Condurctive Silver Ink has many different uses:  "Liquid wire" for model making and electronic work.  Especially suitable for difficult areas. As an artist's paint, for grey metal paints For cars, repair works, preparation for galvanizing, handicraft and painting, model making such as aircraft, ships, railroads.  Adheres to almost all surfaces. If in doubt, make a small test before application. Water-based, solvent-free. The paint dries solid, is highly elastic and water-insoluble with grayish yellow color. And can be painted over with most other paints. High mechanical strength. Quantity depending on the substrate, usually 2-3 strokes with a thin brush. Average grain size under approx. 15µm Keep away from children. Dilutable and brush cleaning with water. Shake well before use, stir up better, also stir up again in between while working the heavy silver particles sink down quickly.      H225 Highly flammable liquid and vapor  flammable. H336 May cause drowsiness or dizziness.  May cause drowsiness or dizziness. H410 Precautionary statements Very toxic to aquatic life with long lasting  effect. P102 Keep out of the reach of children. P210 Keep away from heat, hot surfaces, sparks, open flames and other  Keep away from heat, hot surfaces, sparks, open flames and other ignition sources.  Do not smoke. P273 Avoid release to the environment. P370+P378 In case of fire: Use sand, extinguishing powder or  alcohol-resistant foam for extinguishing. P391 Take up spillage. P403+P235 Store in a well-ventilated place. Keep cool  P501 Collect in suitable, closed containers and take for disposal.