Copper Anode sheet

Alkaline Copper Electrolyte – Cyanide-Free Copper Bath for Acid-Sensitive MetalsProfessional Alkaline Copper Electrolyte for Tank, Pen and Brush PlatingThe Alkaline Copper Electrolyte from Betzmann Galvanik is a high-quality, cyanide-free copper electrolyte for the electroplating of acid-sensitive metals. It has been specially developed to reliably apply firmly adhering copper coatings on materials such as iron, steel, zinc and zinc die-cast alloys.Unlike acidic copper electrolytes, the alkaline copper electrolyte is ideally suited as an adhesion layer and intermediate coating for materials that may be attacked by acidic electrolytes.The electrolyte is suitable for both tank plating and pen/brush plating (tampon plating) and enables uniform, decorative and functional copper coatings at room temperature.Your AdvantagesCyanide-free alkaline copper electrolyteIdeal for acid-sensitive metalsExcellent adhesion on iron and steelVery good leveling propertiesGood throwing powerIntensive, attractive copper colourIdeal intermediate layer before bright copper platingSuitable for tank, pen and brush platingEasy application at room temperatureProfessional quality from Betzmann GalvanikWhy Use Alkaline Copper Plating?Many metals cannot be directly plated with an acidic copper electrolyte. Especially iron, steel and zinc require a special copper strike layer to achieve a permanently adherent copper coating.The alkaline copper electrolyte enables:Strongly adherent copper coatings on iron-based materialsProtection of sensitive base materialsPreparation for further electroplating processesConstruction of high-quality multilayer coating systemsAfter alkaline copper plating, the surface can be further processed with a bright acid copper electrolyte to achieve an especially smooth and glossy finish.Typical ApplicationsIdeal for:IronSteelZincZinc die-cast partsBrassBronzeCopperTinLeadMetal restorationClassic car partsModel makingJewellery manufacturingRepair workTechnical coatingsSuitable Base MaterialsSuitable for:✓ Lead✓ Bronze✓ Iron✓ Steel✓ Copper✓ Brass✓ Zinc✓ Zinc die-cast alloys✓ TinNot directly suitable for:✗ Aluminium✗ Chromium✗ TitaniumAluminium requires suitable pretreatment, for example with an aluminium activator.For unknown materials, a test coating should always be performed before application.Application InstructionsFor optimum results, workpieces must be thoroughly cleaned before copper plating.Remove:OilGreaseDirtOxide layersRustUse clean disposable gloves to prevent renewed contamination from skin oils.The alkaline copper electrolyte already works at room temperature and can be heated if required.The optimum operating temperature range is between 25 and 50 °C.Recommended Layer System for Perfect SurfacesA proven electroplating system:Base Material → Alkaline Copper → Bright Copper → Nickel → Gold / Chromium / Precious MetalsThe alkaline copper electrolyte provides excellent adhesion, while the bright copper electrolyte creates a smooth and highly reflective surface.Technical DataOperating DataCyanide-free alkaline copper electrolytepH value: 8–10Operating temperature: 20–60 °CWorking ConditionsCurrent density: 0.2–1.5 A/dm²Up to 3 A/dm² with solution movementTank Plating:Approx. 1.4 Volts (5 cm electrode distance)Approx. 1.5 Volts (10 cm electrode distance)Approx. 1.7 Volts (20 cm electrode distance)Pen and Brush Plating:2.5–6 VoltsRecommended: 4–5 VoltsAdditional parameters:Plating time: 10–45 minutesDeposition rate:approx. 0.4 µm/min at 1 A/dm² and 20 °CAnode material: Copper AnodeCoating PropertiesUniform copper coatingsExcellent adhesionVery good levelingGood throwing powerAttractive copper colourIdeal preparation for further electroplating processesSupplied AsReady-to-use alkaline copper electrolyteAvailable in various container sizesQuality from Betzmann GalvanikBetzmann Galvanik develops professional electrolytes for decorative and technical surface finishing. The Alkaline Copper Electrolyte is the ideal solution for safe and reliable copper plating of acid-sensitive metals such as iron, steel and zinc and provides the perfect foundation for high-quality multilayer electroplating systems.

PP Copper Electrolyte BMG‑130.1 High-Gloss Copper Plating Solution for Electroplating Applications Short Description The PP Copper Electrolyte BMG‑130.1 is a high-performance electroplating solution for depositing bright, uniform copper layers. It produces thick, glossy coatings suitable for decorative surfaces, functional layers, or as a foundation for further electroplating processes such as nickel or gold. Applications The PP Copper Electrolyte is versatile and can be used for: Electrolytic copper plating of metallic surfaces Protective layers on iron and steel for corrosion resistance Intermediate layer or primer for nickel, gold, or other metals Coating conductive paint on plastics Decorative copper-red finishes Solderable layers for PCBs and electronic boards Its balanced composition makes it suitable for both hobbyist and professional applications in workshops, labs, or industrial environments. How Copper Electroplating Works (Simple Explanation) Electroplating uses direct current (DC) to reduce copper ions from the electrolyte onto the surface: Prepare the workpiece: Clean and degrease. Plating: Connect the workpiece as the cathode; use a graphite or copper anode. Deposition: Copper forms a thick, glossy layer. Post-treatment: Rinse with water and dry – the surface exhibits the characteristic bright copper-red shine. Benefits of PP Copper Electrolyte BMG‑130.1 Bright, uniform, glossy copper layers Thicker deposits than many standard copper solutions Excellent adhesion on conductive substrates Ideal as a base layer for nickel, gold, or other metals Easy to use with graphite or copper anodes Versatile application on plastics with conductive paint Technical Parameters (Guideline Values) PropertyValue / RangeProduct typePP Copper ElectrolyteElectrolyte typeBright copper plating solutionVoltageapprox. 3 V and aboveTemperature14–25 °CCopper content> 60 g/LDeposition rateapprox. 2 µm/min at 3.5 VLayer hardnessapprox. 380–385 HVLayer density8.8 g/cm³Anode materialGraphite or copperApplicationBath, pen, or tampon electroplating Note: Values are practical guidelines; results may vary depending on equipment, voltage, and temperature. Practical Application Instructions Preparation: Clean and degrease surfaces. For non-conductive parts, apply a conductive paint first. Plating: Operate the electrolyte within recommended voltage and temperature ranges. Use graphite or copper anodes for uniform layers. Post-Treatment: Rinse plated parts with water and dry. Light polishing can further enhance gloss if desired. Safety Instructions Wear protective gloves, goggles, and appropriate clothing Avoid contact with skin and eyes Rinse immediately with water if contact occurs Work in well-ventilated areas Do not ingest; keep out of reach of children Dispose according to local chemical waste regulations Conclusion The PP Copper Electrolyte BMG‑130.1 is a high-performance and versatile solution for producing bright, uniform copper layers. Whether for decorative finishes, corrosion protection, or as a foundation for further electroplating, it provides excellent layer quality, easy handling, and professional results for hobbyists, workshops, and industrial applications.

Turn Non-Conductive Surfaces into Conductive Metal Finishes Our Copper Conductive Paint 50 ml or 200 ml is a professional-grade conductive coating designed to transform non-conductive materials into electrically conductive surfaces. It provides the ideal foundation for electroplating while also creating an attractive metallic copper finish for decorative applications. Perfect for 3D printed parts, plastics, resin, wood, ceramics, glass, plaster, and natural materials, this conductive paint allows virtually any object to be prepared for further metal plating. Key Features ✔ Creates electrically conductive surfaces ✔ Ideal primer for electroplating ✔ Excellent adhesion on most non-conductive materials ✔ Bright metallic copper finish ✔ Suitable for brush, sponge, or airbrush application ✔ Easy to apply ✔ Fast drying ✔ Professional quality for industrial and hobby applications Perfect For Electroplating preparation Plastic metallization 3D printed parts PLA and ABS components Resin models Glass metallization Ceramic coating Wood metallization Plaster coating Jewelry manufacturing Model making Restoration projects Decorative metal finishes Art and sculpture Prototype development DIY electroplating Ideal Base for Electroplating After drying, the copper conductive coating forms an electrically conductive surface suitable for electroplating. For maximum conductivity and excellent plating performance, we recommend activating the coated object in an acid copper plating bath. Once the copper layer has been built up, additional metal finishes such as: Nickel Silver Gold Rhodium Chrome can be applied. For premium decorative coatings, a palladium strike layer is recommended before precious metal plating. Easy Application Clean, dry, and degrease the surface thoroughly. Stir or shake the paint well before use. Apply evenly using a brush, sponge, or airbrush. Allow the coating to dry completely. Activate the surface in an acid copper electroplating bath. Continue with additional electroplating processes if desired. Applications Ideal for: Electroplating Jewelry manufacturing Model making Art and sculpture Restoration Electronics prototyping Decorative metal finishing Industrial applications Research and laboratory work Technical Specifications Product Type: Copper Conductive Paint Volume: 50 ml or 200 ml Color: Copper Application: Conductive metallizing coating Application Methods: Brush, sponge, airbrush Suitable Materials: Plastic, PLA, ABS, resin, glass, ceramic, wood, plaster, natural materials Further Processing: Suitable for electroplating Quality: Professional grade Why Choose Copper Conductive Paint? Copper offers excellent electrical conductivity and is the preferred base layer for electroplating applications. This conductive coating creates a reliable conductive surface that enables high-quality plating with nickel, silver, gold, rhodium, chrome, and other metals. Whether you're producing professional prototypes, metallizing 3D prints, restoring artwork, or creating decorative metal finishes, this copper conductive paint delivers reliable, consistent, and professional results. Package Contents 1 × Copper Conductive Paint (50 ml or 200 ml)

S Stainless Steel & Nickel Activator – Professional Deplating / Pickling Solution for Optimal Electroplating AdhesionSurface Activation for Stainless Steel, Nickel and Passive Metal SurfacesThe Stainless Steel & Nickel Activator from Betzmann Galvanik is a professional pickling and activation solution designed to prepare stainless steel, nickel and passive metal surfaces before electroplating.High-alloy metals such as stainless steel and nickel naturally form a very stable oxide and passive layer on their surface. Although this layer provides excellent corrosion resistance, it can significantly reduce the adhesion of subsequent electroplated coatings and may cause problems such as poor adhesion, peeling or uneven deposits.The activator removes these interfering passive layers and creates a chemically active metal surface that is optimally prepared for subsequent electroplating processes.Suitable for applications such as:Nickel platingGold platingSilver platingChrome platingOther electroplating processesYour Advantages at a Glance✔ Removes oxide and passive layers✔ Activates stainless steel and nickel for improved adhesion✔ Prevents adhesion problems during electroplating✔ Suitable for non-electrolytic and electrolytic applications✔ Ideal for pen plating, tampon plating and tank plating✔ Fast and easy application✔ Improves the quality and durability of electroplated coatings✔ Professional surface preparation for high-quality resultsWhy Is an Activator Necessary?Metals such as stainless steel and nickel can quickly form a passive layer when exposed to air.This layer is an excellent protection against corrosion, but it can prevent a strong bond between the base material and the following electroplated coating.Without proper activation, problems may occur:Poor coating adhesionPeeling or flaking of the depositSpottingUneven coatingsPremature coating failureThe activator creates a freshly activated surface and provides the ideal foundation for the next electroplating step.Application Without Electricity (Immersion Process)The activation can easily be carried out without a power supply.Procedure:Thoroughly degrease the workpiece.Immerse the workpiece in the activator.Activate for approx. 30–60 seconds.Rinse thoroughly with water.Continue directly with electroplating.For improved performance, the activator can be heated.Recommended temperature:Usable at room temperatureHeating to approx. 40 °C improves the activation performanceThe increased temperature accelerates the removal of oxide and passive layers and provides a more effective surface activation.Application With Electricity (Electrolytic Activation)For especially reliable results, the activator can also be used electrolytically.This method is particularly suitable for:Stainless steelPassive nickel surfacesDifficult-to-activate materialsProcedure:Thoroughly degrease the workpiece.Connect the workpiece to the negative pole.Connect a stainless steel or suitable electrode to the positive pole.Treat the surface with the activator.Rinse thoroughly and proceed immediately with electroplating.Recommended values:Voltage: approx. 4 voltsElectrode: stainless steel or graphiteActivation time: approx. 30–60 secondsElectrolytic activation supports the removal of passive layers and creates a highly active surface for excellent coating adhesion.Suitable MaterialsThe activator is especially suitable for:Stainless steelNickelPassive nickel surfacesSteelCopperBrassVarious metal alloysFor unknown materials, we recommend testing on an inconspicuous area before use.Processing After ActivationAfter activation, the workpiece should be electroplated as soon as possible.Recommended process:Activate → Rinse → Electroplate immediatelyActivated metal surfaces can change again when exposed to air, so quick further processing ensures the best results.Typical ApplicationsIdeal for:Jewellery electroplatingStainless steel coatingRepair platingIndustrial applicationsPrecision engineeringRestoration workMechanical engineeringMetal finishingGold plating stainless steelNickel plating difficult materialsTechnical InformationProduct type:Activator / Pickling solutionApplication:Surface preparation before electroplatingProcesses:Non-electrolytic activation (immersion process)Electrolytic activation (pen/tampon process)Activation time:Approx. 30–60 secondsTemperature:Room temperature possibleHeating up to approx. 40 °C improves performanceVoltage for electrolytic application:Approx. 4 voltsSuitable electrodes:Stainless steelGraphiteSafety InformationWear safety glasses and suitable protective gloves.Avoid contact with skin and eyes.Use only in well-ventilated areas.Observe the safety data sheet.Do not inhale vapours or aerosols.Quality from Betzmann GalvanikThe Stainless Steel & Nickel Activator is an essential step for professional electroplating applications.By reliably removing oxide and passive layers, it creates an optimally prepared surface for strongly adherent, uniform and durable metal coatings.SEO Shopware 6Product Title:Stainless Steel & Nickel Activator – Pickling Solution for Electroplating PreparationSEO URL:stainless-steel-nickel-activator-pickling-solutionSEO Title:Stainless Steel Nickel Activator | Pickling Solution for ElectroplatingMeta Description:Professional stainless steel and nickel activator for electroplating preparation. Removes oxide and passive layers for excellent adhesion during gold plating, nickel plating, silver plating and chrome plating.Keywords:stainless steel activator, nickel activator, pickling solution electroplating, stainless steel electroplating preparation, activate stainless steel, activate nickel, remove passive layer, remove oxide layer, electroplating preparation, pen plating activator, tampon plating activator, gold plating stainless steelLong-Tail Keywords:stainless steel activator before gold plating, nickel pickling solution for electroplating, improve stainless steel plating adhesion, remove stainless steel passive layer, electrolytic stainless steel activation, immersion activator for electroplating

Bright Acid Copper Electrolyte – Ready-to-Use Copper Plating Solution for Tank, Pen & Brush PlatingProfessional Bright Copper Electrolyte for Brilliant, Smooth and Highly Conductive Copper CoatingsThe Bright Acid Copper Electrolyte from Betzmann Galvanik is a premium, ready-to-use electroplating solution developed for producing brilliant, smooth and highly adherent copper coatings. Its excellent leveling properties and high deposition rate make it ideal for both decorative and technical electroplating applications.The electrolyte produces bright copper deposits with outstanding surface quality, often eliminating the need for extensive polishing. It is perfectly suited for tank plating, pen plating and brush plating, delivering professional results for workshops, jewellery manufacturers, restoration specialists and industrial applications.Your AdvantagesReady-to-use bright acid copper electrolyteBrilliant, high-gloss copper finishHigh deposition rateExcellent leveling propertiesUniform coating thicknessOutstanding adhesionHighly conductive copper depositsExcellent ductilityEasy to polishIdeal base layer for precious metal platingSuitable for tank, pen and brush platingProfessional quality from Betzmann GalvanikTypical ApplicationsPerfect for:Jewellery manufacturingJewellery repairWatchmakingElectronicsPrinted circuit boards (PCB)Electrical contactsDecorative metal finishingMetal restorationAutomotive partsClassic car restorationMechanical engineeringModel makingPrototype manufacturingIndustrial electroplatingWhy Copper Plate?Copper is one of the most important metals used in electroplating. It serves as an excellent intermediate layer, improves adhesion between different metals, and provides outstanding electrical and thermal conductivity.Bright copper coatings are commonly used for:Decorative finishesCorrosion protection systemsElectrical conductivityThermal conductivitySurface levelingIntermediate layers before further platingThe excellent leveling capability helps fill minor surface imperfections, resulting in smoother finishes and significantly reducing polishing time.Ideal Base Layer for Gold, Silver, Nickel and ChromiumBright copper is frequently used as the first layer in high-quality multilayer electroplating systems.Typical coating systems include:Copper → Nickel → GoldorCopper → Nickel → ChromiumThe nickel layer acts as a diffusion barrier, preventing copper migration into precious metal coatings and ensuring long-lasting colour stability and corrosion resistance.Suitable Base MaterialsSuitable for direct plating on acid-resistant metals such as:CopperBrassBronzeNickelNickel-plated surfacesSteel, iron and zinc should first receive an alkaline copper strike before applying the bright acid copper layer.Not suitable for direct plating on:AluminiumTitaniumChromiumTinZincThese materials require appropriate pretreatment.ApplicationFor optimum adhesion, all workpieces should be thoroughly cleaned, degreased and, where required, activated before plating.The use of a Copper Anode is recommended to maintain a constant copper concentration and maximise electrolyte life.Technical SpecificationsElectrolyte DataReady-to-use bright acid copper electrolytepH value: approx. 1Operating temperature: 15–40 °CRecommended Operating ConditionsCurrent density: 2.5–5 A/dm²Up to 7 A/dm² with solution agitationTank plating:Approx. 1.1 Volts (5 cm electrode distance)Approx. 1.7 Volts (10 cm electrode distance)Approx. 2.8 Volts (20 cm electrode distance)Pen & Brush plating:1.2–4.5 VoltsRecommended: Approx. 3 VoltsPlating time: 3–30 minutesDeposition rate: Approx. 1 µm/min at 5 A/dm² and 20 °CAnode material: Copper AnodeCoating PropertiesBrilliant bright copper finishExcellent levelingUniform coating thicknessOutstanding adhesionExcellent ductilityHigh electrical conductivityHigh thermal conductivityExcellent polishing characteristicsIdeal base layer for nickel, chromium, gold, silver and palladium platingSupplied AsReady-to-use Bright Acid Copper ElectrolyteAvailable in various container sizesQuality from Betzmann GalvanikBetzmann Galvanik develops premium electroplating solutions for decorative and technical surface finishing. The Bright Acid Copper Electrolyte combines excellent leveling properties, a high deposition rate and brilliant surface quality, making it the perfect choice for professional copper plating as well as a base layer for nickel, chromium, gold, silver and palladium coatings.

Copper Brightener (Acid / PP Stabilizer) Short Description The Copper Brightener (acid / PP stabilizer) is a performance additive for acidic and PP copper electroplating solutions that enhances the brightness, smoothness, and quality of plated copper layers. It can also revitalize used electrolyte solutions, restoring their ability to produce highly reflective and even copper finishes. What Is This Brightener Used For? This brightener is used to: Improve the brightness of copper electroplated surfaces Enhance performance of acidic and PP copper baths Refresh spent plating solutions for renewed performance Use in bath and pen plating for both decorative and functional coatings How the Brightener Works (Simple Explanation) Special additives in electroplating solutions help refine the deposition process so that copper deposits smoothly, evenly, and with higher gloss. This brightener is added to the electrolyte and works directly within the plating bath: Prepare and operate your copper electrolyte as usual. Add the brightener: e.g., approx. 4 mL per 1 L of electrolyte. Mix and plate: The electrolyte now deposits highly reflective copper immediately. Benefits of the Copper Brightener Enhanced brightness and surface quality of copper coatings Simple to add to both fresh and used electrolytes Suitable for acidic and PP copper solutions Ideal for bath and pen plating Produces smooth, decorative finishes  Application Notes Recommended dosage: approx. 4 mL additive per 1 L electrolyte Mix thoroughly before plating Performance may vary with electrolyte condition, temperature and current; test runs advised  Safety Instructions Wear protective gloves and eye protection Avoid contact with skin and eyes Rinse thoroughly with water if contact occurs Use only in well‑ventilated areas Do not ingest; keep out of reach of children Dispose of chemical waste according to local regulations Conclusion The Copper Brightener (acid / PP stabilizer) is a practical additive that significantly improves the gloss and quality of copper electroplating results. It is easy to use and especially valuable for applications where bright, smooth, high‑quality copper finishes are desired, whether in decorative or functional electroplating. 

Brightener "Zinc" (50 ml) – Additive for Brilliant Zinc Electroplating ResultsZinc Electrolyte Brightener – For Bright, Uniform and High-Quality Zinc CoatingsThe "Zinc" Brightener (50 ml) has been specially developed for use with zinc electrolytes and helps to achieve uniform, bright and highly glossy zinc coatings. It is ideal for refreshing used zinc electrolytes as well as improving the performance of fresh electroplating baths.Just 50 ml of brightener is sufficient for 5 litres of zinc electrolyte. The specially formulated brightening agents improve the surface quality, support an even metal deposition and provide an attractive, shiny finish on galvanically deposited zinc coatings.The brightener is particularly recommended for tank plating and is an ideal addition for anyone who wants to achieve consistently high-quality zinc plating results.Your Advantages at a GlanceBrightener additive for zinc electrolytesProduces bright and uniform zinc coatingsRefreshes used zinc plating bathsSuitable for optimizing fresh zinc electrolytesEasy dosage and application50 ml is sufficient for up to 5 litres of zinc electrolyteEspecially suitable for tank platingImproves the appearance of zinc depositsSimple to useProfessional quality for hobby, workshop and industrial applicationsApplicationThe brightener is added directly to the zinc electrolyte.Dosage:50 ml brightener per 5 litres of zinc electrolyteEquivalent to 10 ml per litre of electrolyteAfter adding the brightener, mix the electrolyte thoroughly. The product can be used both for refreshing used zinc electrolytes and for optimizing freshly prepared zinc plating baths.ApplicationsThe zinc brightener is ideal for:Zinc electroplatingTank platingMaintenance and refreshing of zinc plating bathsImproving zinc coating appearanceWorkshopsHobby electroplatingIndustrial surface finishingRestoration projectsMetal finishing applicationsDelivery Contents1 × Zinc BrightenerQuantity: 50 mlQuality from Betzmann GalvanikThe "Zinc" Brightener provides an easy and effective way to maintain and improve the performance of zinc electrolytes. Even small quantities help create smoother, brighter and more attractive zinc coatings, ensuring consistently high-quality electroplating results.