Alkaline Copper Electrolyte – Cyanide-Free Copper Bath for Acid-Sensitive MetalsProfessional Alkaline Copper Electrolyte for Tank, Pen and Brush PlatingThe Alkaline Copper Electrolyte from Betzmann Galvanik is a high-quality, cyanide-free copper electrolyte for the electroplating of acid-sensitive metals. It has been specially developed to reliably apply firmly adhering copper coatings on materials such as iron, steel, zinc and zinc die-cast alloys.Unlike acidic copper electrolytes, the alkaline copper electrolyte is ideally suited as an adhesion layer and intermediate coating for materials that may be attacked by acidic electrolytes.The electrolyte is suitable for both tank plating and pen/brush plating (tampon plating) and enables uniform, decorative and functional copper coatings at room temperature.Your AdvantagesCyanide-free alkaline copper electrolyteIdeal for acid-sensitive metalsExcellent adhesion on iron and steelVery good leveling propertiesGood throwing powerIntensive, attractive copper colourIdeal intermediate layer before bright copper platingSuitable for tank, pen and brush platingEasy application at room temperatureProfessional quality from Betzmann GalvanikWhy Use Alkaline Copper Plating?Many metals cannot be directly plated with an acidic copper electrolyte. Especially iron, steel and zinc require a special copper strike layer to achieve a permanently adherent copper coating.The alkaline copper electrolyte enables:Strongly adherent copper coatings on iron-based materialsProtection of sensitive base materialsPreparation for further electroplating processesConstruction of high-quality multilayer coating systemsAfter alkaline copper plating, the surface can be further processed with a bright acid copper electrolyte to achieve an especially smooth and glossy finish.Typical ApplicationsIdeal for:IronSteelZincZinc die-cast partsBrassBronzeCopperTinLeadMetal restorationClassic car partsModel makingJewellery manufacturingRepair workTechnical coatingsSuitable Base MaterialsSuitable for:✓ Lead✓ Bronze✓ Iron✓ Steel✓ Copper✓ Brass✓ Zinc✓ Zinc die-cast alloys✓ TinNot directly suitable for:✗ Aluminium✗ Chromium✗ TitaniumAluminium requires suitable pretreatment, for example with an aluminium activator.For unknown materials, a test coating should always be performed before application.Application InstructionsFor optimum results, workpieces must be thoroughly cleaned before copper plating.Remove:OilGreaseDirtOxide layersRustUse clean disposable gloves to prevent renewed contamination from skin oils.The alkaline copper electrolyte already works at room temperature and can be heated if required.The optimum operating temperature range is between 25 and 50 °C.Recommended Layer System for Perfect SurfacesA proven electroplating system:Base Material → Alkaline Copper → Bright Copper → Nickel → Gold / Chromium / Precious MetalsThe alkaline copper electrolyte provides excellent adhesion, while the bright copper electrolyte creates a smooth and highly reflective surface.Technical DataOperating DataCyanide-free alkaline copper electrolytepH value: 8–10Operating temperature: 20–60 °CWorking ConditionsCurrent density: 0.2–1.5 A/dm²Up to 3 A/dm² with solution movementTank Plating:Approx. 1.4 Volts (5 cm electrode distance)Approx. 1.5 Volts (10 cm electrode distance)Approx. 1.7 Volts (20 cm electrode distance)Pen and Brush Plating:2.5–6 VoltsRecommended: 4–5 VoltsAdditional parameters:Plating time: 10–45 minutesDeposition rate:approx. 0.4 µm/min at 1 A/dm² and 20 °CAnode material: Copper AnodeCoating PropertiesUniform copper coatingsExcellent adhesionVery good levelingGood throwing powerAttractive copper colourIdeal preparation for further electroplating processesSupplied AsReady-to-use alkaline copper electrolyteAvailable in various container sizesQuality from Betzmann GalvanikBetzmann Galvanik develops professional electrolytes for decorative and technical surface finishing. The Alkaline Copper Electrolyte is the ideal solution for safe and reliable copper plating of acid-sensitive metals such as iron, steel and zinc and provides the perfect foundation for high-quality multilayer electroplating systems.

White Bronze Electrolyte SW10011.1 Fast plating electrolyte for bright white bronze coatings as an alternative to nickel Short Description The White Bronze Electrolyte SW10011.1 is a brush or bath electroplating solution for depositing a bright white bronze alloy on conductive metal surfaces. When used, it produces an antimicrobial white bronze layer that can replace traditional nickel plating, replicating similar hardness and color while avoiding nickel allergy issues. Real Gold Applications This bronze plating electrolyte is used to: Apply bright white bronze coatings on a variety of metals Replace nickel plating where nickel avoidance is desired Provide corrosion-resistant and antimicrobial layers Act as a barrier layer between copper/brass and gold Create decorative or functional coatings in brush or bath plating Real Gold How It Works (Simple Explanation) White bronze plating is achieved by mixing this electrolyte with an alkaline copper plating solution (1:1) and applying direct current. The bronze alloy deposits as a uniform, bright metallic layer. Real Gold Benefits High deposition rates and efficient operation Nickel-free alternative with similar physical properties Antimicrobial and corrosion-resistant surface Functions as a barrier layer before gold plating Decorative and functional surface finish Compatible with brush and bath plating Real Gold Typical Parameters PropertyValue / RangeElectrolyte typeWhite bronze plating solutionMixing ratio1 part alkaline copper : 1 part White BronzeVoltage3.2–3.5 VTemperature18–25 °C (optimum ~22 °C)ElectrodeGraphite/platinumTypical alloy~42 % Cu / 58 % SnHardness450–500 HVDensity of deposit8.6–8.8 g/cm³Plating rate0.7–1.5 µm/minShelf life~4 weeks if stored correctlyStorage2–5 °C recommendedAir sensitiveYes — keep sealed Safety Information Follow all standard electroplating safety practices: Wear protective gloves, goggles, and clothing Avoid contact with skin and eyes Use in well-ventilated areas Keep out of reach of children Dispose of wastes per local regulations Conclusion The White Bronze Electrolyte SW10011.1 is a versatile plating solution that produces bright, antimicrobial white bronze coatings with mechanical and aesthetic properties close to nickel plating. It is especially useful where nickel use is restricted or undesirable, and as a barrier layer prior to gold plating in both decorative and functional applications.

White Bronze Electrolyte SW10011.1 Fast plating electrolyte for bright white bronze coatings as an alternative to nickel Short Description The White Bronze Electrolyte SW10011.1 is a brush or bath electroplating solution for depositing a bright white bronze alloy on conductive metal surfaces. When used, it produces an antimicrobial white bronze layer that can replace traditional nickel plating, replicating similar hardness and color while avoiding nickel allergy issues. Real Gold Applications This bronze plating electrolyte is used to: Apply bright white bronze coatings on a variety of metals Replace nickel plating where nickel avoidance is desired Provide corrosion-resistant and antimicrobial layers Act as a barrier layer between copper/brass and gold Create decorative or functional coatings in brush or bath plating Real Gold How It Works (Simple Explanation) White bronze plating is achieved by mixing this electrolyte with an alkaline copper plating solution (1:1) and applying direct current. The bronze alloy deposits as a uniform, bright metallic layer. Real Gold Benefits High deposition rates and efficient operation Nickel-free alternative with similar physical properties Antimicrobial and corrosion-resistant surface Functions as a barrier layer before gold plating Decorative and functional surface finish Compatible with brush and bath plating Real Gold Typical Parameters PropertyValue / RangeElectrolyte typeWhite bronze plating solutionMixing ratio1 part alkaline copper : 1 part White BronzeVoltage3.2–3.5 VTemperature18–25 °C (optimum ~22 °C)ElectrodeGraphite/platinumTypical alloy~42 % Cu / 58 % SnHardness450–500 HVDensity of deposit8.6–8.8 g/cm³Plating rate0.7–1.5 µm/minShelf life~4 weeks if stored correctlyStorage2–5 °C recommendedAir sensitiveYes — keep sealed Safety Information Follow all standard electroplating safety practices: Wear protective gloves, goggles, and clothing Avoid contact with skin and eyes Use in well-ventilated areas Keep out of reach of children Dispose of wastes per local regulations Conclusion The White Bronze Electrolyte SW10011.1 is a versatile plating solution that produces bright, antimicrobial white bronze coatings with mechanical and aesthetic properties close to nickel plating. It is especially useful where nickel use is restricted or undesirable, and as a barrier layer prior to gold plating in both decorative and functional applications.

Bright Nickel Electrolyte – Ready-to-Use Nickel Plating Solution for Tank, Pen and Brush PlatingProfessional Bright Nickel Electrolyte for Highly Glossy, Corrosion-Resistant and Wear-Resistant Nickel CoatingsThe Bright Nickel Electrolyte from Betzmann Galvanik is a premium-quality, ready-to-use electroplating solution developed for depositing brilliant, highly reflective nickel coatings. It is suitable for both decorative and technical electroplating applications and can be used in tank plating, pen plating, and brush plating.The deposited nickel coatings provide excellent corrosion protection, high hardness, outstanding adhesion, and a bright silver-like finish with the characteristic warm tone of pure nickel. Bright nickel is widely used both as an attractive decorative finish and as a functional intermediate layer for subsequent precious metal coatings.This professional electrolyte is suitable for hobby users, workshops, jewelry manufacturers, restoration specialists, and industrial electroplating applications.Your AdvantagesReady-to-use bright nickel electrolyteBrilliant high-gloss nickel finishExcellent corrosion protectionOutstanding wear resistanceHigh chemical resistanceIdeal diffusion barrier for precious metal platingSuitable for tank, pen, and brush platingDecorative and technical applicationsEasy to useProfessional quality from Betzmann GalvanikTypical ApplicationsPerfect for:Jewelry manufacturingJewelry repairWatchmakingClassic car restorationMotorcycle partsAutomotive componentsMechanical engineeringModel makingMetal finishingElectrical contactsElectronic componentsDecorative metal partsIndustrial electroplatingRestoration projectsExcellent Corrosion Protection and Decorative FinishNickel is one of the most important electroplating metals worldwide. Even relatively thin nickel coatings significantly improve corrosion resistance while protecting metal surfaces against humidity, water, air, diluted acids, and alkaline solutions.For maximum corrosion protection, the classic plating sequence is recommended:Copper → Bright Nickel → ChromiumThis combination produces an exceptionally durable, highly reflective, and wear-resistant surface.Bright nickel can also be used as a decorative final finish without an additional chromium layer.Ideal Diffusion BarrierBright nickel is frequently used as an effective diffusion barrier between copper and precious metal coatings. It prevents migration of base metals into the final coating and maintains long-term colour stability.It is the ideal intermediate layer before:Gold platingRose gold platingWhite gold platingSilver platingPalladium platingRhodium platingBlack rhodium platingRuthenium platingChromium platingSuitable Base MaterialsSuitable for plating:SteelIronCopperBrassBronzeSilverGoldNickelNickel alloysStainless steel should first be activated using a suitable Nickel Strike to ensure excellent adhesion.Not suitable for direct plating on:AluminiumTitaniumChromiumZincThese materials require appropriate pretreatment or specialised intermediate coatings.ApplicationBefore plating, all workpieces should be thoroughly cleaned, degreased, and, where necessary, derusted.For best results, follow these preparation steps:CleanDegreaseActivateNickel plateRinseApply additional decorative coatings if requiredThe use of a Nickel Anode is highly recommended to maintain a constant nickel concentration and maximise electrolyte service life.The magnetic properties of ferromagnetic workpieces remain unchanged after nickel plating.Technical SpecificationsElectrolyte DataReady-to-use electrolytepH value: approx. 4Operating temperature: 15–60 °CRecommended Operating ConditionsCurrent density: 0.3–3.0 A/dm²Up to 5 A/dm² with solution agitationTank plating:Approx. 2.8 V (5 cm electrode distance)Approx. 4.0 V (10 cm electrode distance)Approx. 6.6 V (20 cm electrode distance)Pen and brush plating:Approx. 6–12 VoltsRecommended: 8–9 VoltsPlating time: 10–60 minutesDeposition rate: Approx. 0.2 µm/min at 2 A/dm² and 20 °CAnode material: Nickel AnodeCoating PropertiesBrilliant high-gloss nickel finishBright silver-like appearanceCharacteristic warm nickel colourExcellent adhesionOutstanding corrosion resistanceHigh chemical resistanceExcellent wear resistanceEffective diffusion barrierMagnetic properties of the base material remain unchangedSupplied AsReady-to-use Bright Nickel ElectrolyteAvailable in various container sizesQuality from Betzmann GalvanikBetzmann Galvanik develops premium electroplating solutions for decorative and technical surface finishing. The Bright Nickel Electrolyte produces brilliant, uniform nickel coatings with outstanding corrosion protection and is ideal both as a decorative final finish and as a diffusion barrier before precious metal plating in tank plating, pen plating, and brush plating applications.

Graphite Electrode Ø 6 mm – Universal Electrode for Professional ElectroplatingChemically Inert Graphite Electrode for Tank, Pen and Brush PlatingThe Graphite Electrode Ø 6 mm is manufactured from high-quality, high-density fine-grain graphite and is ideal for a wide range of electroplating applications. It is used wherever a metal-free, chemically inert electrical conductor is required and contamination of the electrolyte by metal ions must be avoided.Thanks to its excellent chemical resistance, graphite dissolves only very slowly in the electrolyte. This keeps the electrolyte composition stable and ensures high-quality, uniform plating results.The graphite electrode is perfectly suited for tank plating, pen plating and brush (tampon) plating and is compatible with a wide variety of electroplating solutions.Your AdvantagesManufactured from high-quality fine-grain graphiteChemically inertVery low wearNo contamination of the electrolyte with metal ionsExcellent chemical resistanceUniform current distributionSuitable for a wide range of electroplating processesLong service lifeFits standard 6 mm electrode holdersProfessional quality from Betzmann GalvanikWhy Use a Graphite Electrode?Many electroplating processes require that no additional metal ions enter the electrolyte, as these can negatively affect coating quality.Graphite offers several important advantages:Chemically almost inertVery low solubilityExcellent temperature resistanceGood electrical conductivityNo contamination of the electrolyteThese properties make graphite the preferred choice for many decorative and technical plating applications.Typical ApplicationsIdeal for:Gold platingSilver platingChromium platingPalladium platingPlatinum platingWhite bronze platingBlack nickel platingTank platingPen platingBrush (tampon) platingActivating solutionsCleaning solutionsWorkshopsLaboratoriesIndustrial applicationsRestorationModel makingMaterial PropertiesThe electrode is manufactured from high-density fine-grain graphite and offers:Excellent chemical resistanceGood electrical conductivityLow wearSlow consumption in the electrolyteLong service lifeApplication InstructionsBefore use:Keep the electrode clean and free from greaseUse a suitable electrolyteFollow the recommended voltage and current settingsDuring operation, the graphite electrode wears only slowly. Replacing it when necessary ensures consistently high-quality plating results.Technical SpecificationsMaterial: High-density fine-grain graphiteDiameter: 6 mmExcellent chemical resistanceVery good electrical conductivitySuitable for standard electrode holdersPackage Contents1 × Graphite Electrode Ø 6 mmQuality from Betzmann GalvanikBetzmann Galvanik supplies high-quality electrodes and professional accessories for demanding electroplating applications. The Graphite Electrode Ø 6 mm offers excellent chemical resistance, long service life and universal compatibility, making it the ideal choice for hobby users, workshops and industrial applications.

Anode Fabric Pad Sleeve Fluffy BMG-015 – Uniform Coating & Maximum Control The Anode Fabric Pad Fluffy BMG-015 is a specially designed accessory for pen plating and tampon electroplating, ensuring consistent electrolyte distribution and controlled coating processes. Thanks to its fluffy, high-volume structure, the pad absorbs electrolyte efficiently and releases it evenly and continuously onto the surface. This results in clean, uniform and high-quality metal coatings, even in demanding applications. Key Benefits at a Glance Excellent electrolyte absorption and release Uniform liquid and current distribution Ideal for precise and controlled plating Suitable for: Pen plating Tampon plating Reduces streaking and uneven deposits Flexible and easy to replace Applications Selective metal plating Repair and touch-up work Fine detail applications Jewelry finishing Technical surface treatments Technical Parameters Product Type: Anode fabric pad (fluffy) Item Number: BMG-015 Material: High-absorbency textile fabric Structure: Fluffy / high-volume Function: Electrolyte carrier for anode applications Application Areas: Pen plating Tampon plating Electrolyte Absorption: Very high Electrolyte Release: Even and controlled Current Distribution: Supports uniform deposition Reusability: Limited (depending on application) Replacement: Quick and easy Application – Step by Step 1. Preparation Soak the fabric pad with the appropriate electrolyte Allow excess liquid to drip off slightly Attach to the anode or plating pen 2. Pen Plating Application Move the pad evenly across the surface Maintain consistent contact Control voltage and movement Ensures precise and clean results 3. Tampon Plating Application Use the pad as an electrolyte carrier Apply even pressure Maintain continuous motion  Ideal for selective plating applications Pro Tips for Best Results Replace pad regularly for consistent quality Avoid over-saturation → better control Uniform movement prevents streaks Always use clean electrolyte Conclusion The Anode Fabric Pad Fluffy BMG-015 is an essential accessory for achieving precise, uniform and high-quality results in pen and tampon electroplating. It ensures optimal control, clean finishes and significantly improved coating performance.