Tin
€15.47
Available, delivery time: 1-2 days
Product information "Tin"
Tin Solution - Tin Electrolyte - self tinning from Betzmann Galvanik
Our versatile tin plating solution is used in applications ranging from the cookware industry to high-end electronics.
Recommended electrode: platinum electrode or graphite electrode
From 3 volts
Can be plated on copper, nickel or thin gold layer
Please note: This is an air sensitive solution. When not using the solution, keep the lid tightly closed and take steps to minimize air space in the bottle.
You can do this by adding marbles or glass beads to the bottle, squeezing out the excess air at the top of the bottle, or drawing up the solution and storing it in one of our storage syringes.
Failure to follow the above precautions may result in degeneration of the tin in the solution.
Operating Conditions and Deposit Data
| Plating Factor | 0.01 A/cm2 (see notes) |
| Plating rate | ~0.5 micron per minute at 0.01A/cm2, 20°C with mild agitation |
| Maximum plating thickness | In excess of 1000 microns (1mm) |
| Temperature | 18 – 25 |
| pH | 3.6 – 4.0 |
| Tin concentration | 22 grams per litre |
| Filtration | Continuous through filter pump especiall if anode bags not used. |
| Visual qualities of deposit | Matt to satin finish turning crystaline at thickensses greater than 20 microns |
| Agitation | Medium to vigorous |
| Electrode | Tin |
| Tin content in plate | 99.9% (balance carbon) |
| Cathode efficiency | 100% at Plating Factor = 0.01A/cm2 with mild agitation. |
| Hardness | 1.5 (Mohs Hardness) |
| Density of deposit | White (β): 7.289 g/cm |
| Stress | Low – undetectable |
| Special storage requirements | Store in hermetically sealed container as the tin salt is oxygen sensitive. |
| Shelf life | 1 – 2 years |
| Health and Safety classification | Irritant |
| Special considerations | None. |
| Transport (UN number) | None: Not classified as dangerous for transport |
Notes:
- Higher plating factors can be used and/or anodes used for longer if anode
bags are not used. However continuous filtration wll be necessary.
.gif?ts=1720611308)
Labelling according Regulation (EC) No 1272/2008
Pictogram Signal word Warning Hazard statement(s).
H316 Causes mild skin irritation.
H320 Causes eye irritation.
H335 May cause respiratory irritation.
P261 Avoid breathing dust/ fume/ gas/ mist/ vapours/spray.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
Similar Items
Anode pad / tampon / anode sleeve / fuzzy sleeve / replacement fabric pad puffy from Betzmann Galvanik. This puffy fabric pad / anode sleeve or also called tampon is absolutely recommended for all plating processes. Optimally suitable for all coatings and electrolytes. The coating of larger areas is also quite fast with this pad. The insertion hole is larger than the electrode and therefore it happens that the moist anode pad slips off. Therefore, fix the pad on the electrode with a small rubber band.
Graphite round rod - Graphite rod anode - Graphite electrode for gold plating. Graphite electrodes are ultimate for all coatings. The advantage is that in some coatings with stainless steel electrodes, the dislodged metal parts disturb the coating. This does not happen with graphite electrodes, because graphite also filters out contaminated liquids. With bath electroplating, they also need to be replaced occasionally as they slowly dissolve during the plating process. With pad electroplating, simply loosen the screw on the handle and replace with a new one. Diameter 6 mm, length approx. 9 cm Features Used for Doesn’t contaminate Cleaner Activating and electro-cleaning Its resistive properties help to heat the solution you’re plating with Chromium plating, which needs to be plated at 25 degrees celsius; its natural heating action helps to maintain the solution’s optimal temperature Low cost Can be used for all plating processes but carbon electrodes deteriorate over a period of time and discolour swabs (discolouration does not affect the plating quality)
Stainless steel electrode 6 mm This electrode is ideal for most work steps. It can mainly be used for degreasing, activating, and dechroming, and is also very good for chromium plating.Important! Stainless steel electrodes can cause contamination of the coating solution in other coating processes. In this case, it is recommended to use a more suitable anode, e.g., made of graphite or platinum. Stainless steel electrodes and, ideally, aluminum electrodes are suitable for chromium plating. Graphite or platinum electrodes are suitable for gold plating. Graphite or silver electrodes are suitable for silver plating. Length: 9.5 cm, diameter 6 mm