Anode Fabric Pad Sleeve Fluffy BMG-015 – Uniform Coating & Maximum Control The Anode Fabric Pad Fluffy BMG-015 is a specially designed accessory for pen plating and tampon electroplating, ensuring consistent electrolyte distribution and controlled coating processes. Thanks to its fluffy, high-volume structure, the pad absorbs electrolyte efficiently and releases it evenly and continuously onto the surface. This results in clean, uniform and high-quality metal coatings, even in demanding applications. Key Benefits at a Glance Excellent electrolyte absorption and release Uniform liquid and current distribution Ideal for precise and controlled plating Suitable for: Pen plating Tampon plating Reduces streaking and uneven deposits Flexible and easy to replace Applications Selective metal plating Repair and touch-up work Fine detail applications Jewelry finishing Technical surface treatments Technical Parameters Product Type: Anode fabric pad (fluffy) Item Number: BMG-015 Material: High-absorbency textile fabric Structure: Fluffy / high-volume Function: Electrolyte carrier for anode applications Application Areas: Pen plating Tampon plating Electrolyte Absorption: Very high Electrolyte Release: Even and controlled Current Distribution: Supports uniform deposition Reusability: Limited (depending on application) Replacement: Quick and easy Application – Step by Step 1. Preparation Soak the fabric pad with the appropriate electrolyte Allow excess liquid to drip off slightly Attach to the anode or plating pen 2. Pen Plating Application Move the pad evenly across the surface Maintain consistent contact Control voltage and movement Ensures precise and clean results 3. Tampon Plating Application Use the pad as an electrolyte carrier Apply even pressure Maintain continuous motion  Ideal for selective plating applications Pro Tips for Best Results Replace pad regularly for consistent quality Avoid over-saturation → better control Uniform movement prevents streaks Always use clean electrolyte Conclusion The Anode Fabric Pad Fluffy BMG-015 is an essential accessory for achieving precise, uniform and high-quality results in pen and tampon electroplating. It ensures optimal control, clean finishes and significantly improved coating performance.

White Palladium Electrolyte 10 g/L BMG‑101M High‑Performance Palladium Plating Solution for Bright, Silver‑White Coatings Short Description The White Palladium Electrolyte 10 g/L BMG‑101M is a premium electroplating solution designed to deposit bright, silver‑white palladium layers. With a palladium concentration of approximately 10 g per liter, this electrolyte produces a brilliant, metallic finish that is even more striking than traditional nickel plating. real-gold.de It can be used both as a hard decorative top layer and as a nickel‑free barrier layer in multi‑step plating systems. real-gold.de Applications White palladium plating is suitable for: Applying bright silver‑white palladium coatings Nickel‑free barrier layers between copper/brass and gold Decorative finishes with high corrosion resistance Prepping surfaces for subsequent gold plating Alternatives to silver plating, as palladium does not tarnish easily  This makes it especially useful for jewelry, electronics, and other applications where an elegant, durable, and nickel‑free surface is desired.  How White Palladium Plating Works (Simple Explanation) Palladium electroplating works by using direct current (DC) to reduce palladium ions from the electrolyte onto the surface of the workpiece: Surface Preparation: Clean and degrease the part thoroughly. Plating: Connect the workpiece as the cathode and apply appropriate voltage. Deposition: Palladium ions reduce and form a uniform, silver‑white metallic coating. Finishing: Rinse with water and dry after plating.  Benefits of White Palladium Electrolyte BMG‑101M Extremely bright, silver‑white metallic finish, brighter than traditional nickel coatings  Nickel‑free and allergen‑free, ideal for skin‑contact applications  Acts as an excellent barrier layer between base metals and gold  High corrosion resistance and very low porosity, improving durability  Suitable on many substrates, including copper, nickel, brass, silver, gold, and dechromed surfaces  Can be solder‑wetted and provides strong performance on electrical contacts Technical Parameters (Practical Data) PropertyValue / RangeElectrolyte typePalladium plating solutionPalladium contentapprox. 10 g/LRecommended voltage3.0–3.5 V (pin electroplating from ~3 V, bath 3–4 V)Operating temperature48–52 °CpH7.0–8.0Deposition rateapprox. 0.17 µm/min at 0.0075 A/cm²Hardnessapprox. 488 HVDensity of depositapprox. 11.85 g/cm³Deposit purity~99.9 % palladiumAnodePlatinum mesh or graphiteAgitationVery low (mini stir rod)Lightness (L*)65 (CIE L* value)Shelf life1–2 yearsHealth/Safety classificationIrritantTransport classificationNot classified as hazardous Note: These values are practical guidelines and may vary depending on equipment, voltage, and material.  Practical Application Instructions Surface Preparation: Clean and degrease parts thoroughly to remove oils and contaminants. Plating: Heat the solution to the recommended temperature (48–52 °C). Apply recommended voltage; stable agitation with a mini stir rod improves coating uniformity. Post‑Treatment: Rinse parts with clean water after plating. Dry carefully; light polishing can enhance the finish if desired. Safety Instructions White palladium electroplating solutions contain active chemical components and must be handled with care: Wear protective gloves, eye protection, and suitable clothing Avoid contact with skin and eyes Rinse thoroughly with water if contact occurs Operate in well‑ventilated areas Do not ingest; keep out of the reach of children Dispose of waste according to local chemical waste regulations  Conclusion The White Palladium Electrolyte 10 g/L BMG‑101M is a professional‑grade electroplating solution that delivers very bright, silver‑white palladium coatings with excellent durability and low porosity. It is particularly suitable for decorative and functional applications, and as a nickel‑free barrier layer before gold plating, making it ideal for jewelry, electronics, and precision metalwork

Graphite Electrode Ø 6 mm – Universal Electrode for Professional ElectroplatingChemically Inert Graphite Electrode for Tank, Pen and Brush PlatingThe Graphite Electrode Ø 6 mm is manufactured from high-quality, high-density fine-grain graphite and is ideal for a wide range of electroplating applications. It is used wherever a metal-free, chemically inert electrical conductor is required and contamination of the electrolyte by metal ions must be avoided.Thanks to its excellent chemical resistance, graphite dissolves only very slowly in the electrolyte. This keeps the electrolyte composition stable and ensures high-quality, uniform plating results.The graphite electrode is perfectly suited for tank plating, pen plating and brush (tampon) plating and is compatible with a wide variety of electroplating solutions.Your AdvantagesManufactured from high-quality fine-grain graphiteChemically inertVery low wearNo contamination of the electrolyte with metal ionsExcellent chemical resistanceUniform current distributionSuitable for a wide range of electroplating processesLong service lifeFits standard 6 mm electrode holdersProfessional quality from Betzmann GalvanikWhy Use a Graphite Electrode?Many electroplating processes require that no additional metal ions enter the electrolyte, as these can negatively affect coating quality.Graphite offers several important advantages:Chemically almost inertVery low solubilityExcellent temperature resistanceGood electrical conductivityNo contamination of the electrolyteThese properties make graphite the preferred choice for many decorative and technical plating applications.Typical ApplicationsIdeal for:Gold platingSilver platingChromium platingPalladium platingPlatinum platingWhite bronze platingBlack nickel platingTank platingPen platingBrush (tampon) platingActivating solutionsCleaning solutionsWorkshopsLaboratoriesIndustrial applicationsRestorationModel makingMaterial PropertiesThe electrode is manufactured from high-density fine-grain graphite and offers:Excellent chemical resistanceGood electrical conductivityLow wearSlow consumption in the electrolyteLong service lifeApplication InstructionsBefore use:Keep the electrode clean and free from greaseUse a suitable electrolyteFollow the recommended voltage and current settingsDuring operation, the graphite electrode wears only slowly. Replacing it when necessary ensures consistently high-quality plating results.Technical SpecificationsMaterial: High-density fine-grain graphiteDiameter: 6 mmExcellent chemical resistanceVery good electrical conductivitySuitable for standard electrode holdersPackage Contents1 × Graphite Electrode Ø 6 mmQuality from Betzmann GalvanikBetzmann Galvanik supplies high-quality electrodes and professional accessories for demanding electroplating applications. The Graphite Electrode Ø 6 mm offers excellent chemical resistance, long service life and universal compatibility, making it the ideal choice for hobby users, workshops and industrial applications.