Anode Fabric Pad Sleeve Fluffy BMG-015 – Uniform Coating & Maximum Control The Anode Fabric Pad Fluffy BMG-015 is a specially designed accessory for pen plating and tampon electroplating, ensuring consistent electrolyte distribution and controlled coating processes. Thanks to its fluffy, high-volume structure, the pad absorbs electrolyte efficiently and releases it evenly and continuously onto the surface. This results in clean, uniform and high-quality metal coatings, even in demanding applications. Key Benefits at a Glance Excellent electrolyte absorption and release Uniform liquid and current distribution Ideal for precise and controlled plating Suitable for: Pen plating Tampon plating Reduces streaking and uneven deposits Flexible and easy to replace Applications Selective metal plating Repair and touch-up work Fine detail applications Jewelry finishing Technical surface treatments Technical Parameters Product Type: Anode fabric pad (fluffy) Item Number: BMG-015 Material: High-absorbency textile fabric Structure: Fluffy / high-volume Function: Electrolyte carrier for anode applications Application Areas: Pen plating Tampon plating Electrolyte Absorption: Very high Electrolyte Release: Even and controlled Current Distribution: Supports uniform deposition Reusability: Limited (depending on application) Replacement: Quick and easy Application – Step by Step 1. Preparation Soak the fabric pad with the appropriate electrolyte Allow excess liquid to drip off slightly Attach to the anode or plating pen 2. Pen Plating Application Move the pad evenly across the surface Maintain consistent contact Control voltage and movement Ensures precise and clean results 3. Tampon Plating Application Use the pad as an electrolyte carrier Apply even pressure Maintain continuous motion  Ideal for selective plating applications Pro Tips for Best Results Replace pad regularly for consistent quality Avoid over-saturation → better control Uniform movement prevents streaks Always use clean electrolyte Conclusion The Anode Fabric Pad Fluffy BMG-015 is an essential accessory for achieving precise, uniform and high-quality results in pen and tampon electroplating. It ensures optimal control, clean finishes and significantly improved coating performance.

White Palladium Electrolyte 10 g/L BMG‑101M High‑Performance Palladium Plating Solution for Bright, Silver‑White Coatings Short Description The White Palladium Electrolyte 10 g/L BMG‑101M is a premium electroplating solution designed to deposit bright, silver‑white palladium layers. With a palladium concentration of approximately 10 g per liter, this electrolyte produces a brilliant, metallic finish that is even more striking than traditional nickel plating. real-gold.de It can be used both as a hard decorative top layer and as a nickel‑free barrier layer in multi‑step plating systems. real-gold.de Applications White palladium plating is suitable for: Applying bright silver‑white palladium coatings Nickel‑free barrier layers between copper/brass and gold Decorative finishes with high corrosion resistance Prepping surfaces for subsequent gold plating Alternatives to silver plating, as palladium does not tarnish easily  This makes it especially useful for jewelry, electronics, and other applications where an elegant, durable, and nickel‑free surface is desired.  How White Palladium Plating Works (Simple Explanation) Palladium electroplating works by using direct current (DC) to reduce palladium ions from the electrolyte onto the surface of the workpiece: Surface Preparation: Clean and degrease the part thoroughly. Plating: Connect the workpiece as the cathode and apply appropriate voltage. Deposition: Palladium ions reduce and form a uniform, silver‑white metallic coating. Finishing: Rinse with water and dry after plating.  Benefits of White Palladium Electrolyte BMG‑101M Extremely bright, silver‑white metallic finish, brighter than traditional nickel coatings  Nickel‑free and allergen‑free, ideal for skin‑contact applications  Acts as an excellent barrier layer between base metals and gold  High corrosion resistance and very low porosity, improving durability  Suitable on many substrates, including copper, nickel, brass, silver, gold, and dechromed surfaces  Can be solder‑wetted and provides strong performance on electrical contacts Technical Parameters (Practical Data) PropertyValue / RangeElectrolyte typePalladium plating solutionPalladium contentapprox. 10 g/LRecommended voltage3.0–3.5 V (pin electroplating from ~3 V, bath 3–4 V)Operating temperature48–52 °CpH7.0–8.0Deposition rateapprox. 0.17 µm/min at 0.0075 A/cm²Hardnessapprox. 488 HVDensity of depositapprox. 11.85 g/cm³Deposit purity~99.9 % palladiumAnodePlatinum mesh or graphiteAgitationVery low (mini stir rod)Lightness (L*)65 (CIE L* value)Shelf life1–2 yearsHealth/Safety classificationIrritantTransport classificationNot classified as hazardous Note: These values are practical guidelines and may vary depending on equipment, voltage, and material.  Practical Application Instructions Surface Preparation: Clean and degrease parts thoroughly to remove oils and contaminants. Plating: Heat the solution to the recommended temperature (48–52 °C). Apply recommended voltage; stable agitation with a mini stir rod improves coating uniformity. Post‑Treatment: Rinse parts with clean water after plating. Dry carefully; light polishing can enhance the finish if desired. Safety Instructions White palladium electroplating solutions contain active chemical components and must be handled with care: Wear protective gloves, eye protection, and suitable clothing Avoid contact with skin and eyes Rinse thoroughly with water if contact occurs Operate in well‑ventilated areas Do not ingest; keep out of the reach of children Dispose of waste according to local chemical waste regulations  Conclusion The White Palladium Electrolyte 10 g/L BMG‑101M is a professional‑grade electroplating solution that delivers very bright, silver‑white palladium coatings with excellent durability and low porosity. It is particularly suitable for decorative and functional applications, and as a nickel‑free barrier layer before gold plating, making it ideal for jewelry, electronics, and precision metalwork

Graphite Electrode Ø 6 mm (BMG‑010) Short Description The Graphite Electrode Ø 6 mm (BMG‑010) is a durable, chemically inert electrode rod made from high‑density fine‑grain graphite. Designed for use as an anode or electrode in electroplating processes, it is ideal for bath, pen, and pad plating applications where a clean, metal‑free current supply is essential.  Product Description This graphite electrode is manufactured from highly compressed fine‑grain graphite, which dissolves only slowly in electrolytes. Unlike metallic anodes, graphite does not shed contaminating metal particles, ensuring cleaner coatings and higher deposit quality.  The 6 mm diameter rod, with an approximate length of 95 mm, fits standard plating fixtures, holders, and pen plating tools, making it easy to integrate into various electroplating setups Typical Applications Electroplating processes (e.g., silver, gold, copper, black nickel, chrome, white bronze) Pen, bath, and pad plating Activation and pre‑treatment steps Counter‑electrode or anode use in a wide range of electrolytes Situations where metal contamination must be avoided Key Benefits Chemically inert: prevents unwanted metal ion contamination in the plating bath. Versatile: compatible with most electroplating chemistries and techniques.  Slow wear: dissolves gradually, extending service life. Affordable: cost‑effective solution for frequent use.  Easy to use: fits common plating holders and pen plating tools. Material & Dimensions Material: High‑density fine‑grain graphite Diameter: 6 mm Length: approx. 95 mm (other lengths may be available)  Practical Tips Ensure electrodes are clean and free of oils before use.  Replace electrodes periodically as they slowly dissolve during electroplating. Graphite’s mild warming effect can help stabilize bath temperature during plating. Conclusion The Graphite Electrode Ø 6 mm is an effective and reliable anode/electrode for a wide range of electroplating applications. Its inert behavior, broad compatibility, and metal‑free current delivery make it a solid choice for hobbyists, workshops, labs, and professional plating operations.