Stainless Steel Electrode 6mm

The perfect storage cup for electrode and cloth pad transparent with black lid Large storage beaker - Betzmann Galvanik  This stable beaker with screw cap made of PET holds approx. 370 ml. It is practical for storing the electrode with the fabric pad in the respective electrolyte. On request, you will receive the appropriate labeling for the material to be stored.   PET can with screw cap clear - 370 ml with plastic screw cap black 70 mm   

Galvano activator and decapping agent in one - stainless steel and nickel activator in one - from Betzmann GalvanikThe GALVANO AKTIVATOR from Betzmann Galvanik removes oxide layers on base metals to enable electroplating or electroless plating. The electroplating activator is required, for example, for electroless nickel plating of aluminium or to activate stainless steel, nickel, brass and chrome for electroplating.Discover the versatile application of the activator or decapping agent in electroplating! The activator / decapping agent is an indispensable aid for the decapping and preparation of surfaces before plating in the electroplating industry. It is used to activate surfaces of metals such as steel, copper and copper alloys as well as passive nickel layers. Decapitation removes impurities from surfaces and simultaneously prepares them for the plating process. This process is crucial to ensure optimum adhesion and durability of the coating. After alkaline pre-treatment, the decapping agent is also perfect for neutralising. It ensures that work with sulphuric or hydrochloric acid is no longer necessary, which not only increases efficiency but also improves work safety.With Betzmann Galvanik's decapping agent, you can effectively pre-treat the surface of your products to achieve high-quality electroplated coatings. Rely on its proven performance to optimise your electroplating processes and achieve outstanding results.Field of application: Pre-treatment and cleaner - General applicationThe object is either immersed in the activator for 30 to 60 seconds and then briefly rinsed with clear water or coated with the pad for at least 30 seconds from 2.7 volts. The activator removes thin layers of oxide that are invisible to the naked eye. Carry out further coating quickly after the activator bath, as these layers quickly form again with atmospheric oxygen (time period: max. 10 - 30 minutes) Recommended electrode: Stainless steel electrode or graphite electrode!  Recommended voltage: from 2.7 volts Regulation (EC) No. 1272/2008 Signal word: Warning Pictograms: H319 Causes serious eye irritation Hazard statements P280 Wear protective gloves/protective clothing/eye protection/face protection. P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove any contact lenses if possible. Continue rinsing. P337+P313 If eye irritation persists: Get medical advice/attention.    

  Product information "Gold Flash" from Betzmann Galvanik   Gold Flash with 2 grams of gold per liter - wonderfully suitable as an intermediate layer or decorative layer.    The Gold Flash from Betzmann Galvanik has 2 main areas of application:   1. optical-decorative layer: Gold is soft and needs the addition of cobalt as a hard abrasion resistant top layer, which is not included in this product. Therefore, the gold layer from Goldflash appears somewhat lighter yellow. Parts that are not subject to any stress, such as souvenirs, horseshoes for decoration, etc., can be easily, directly and inexpensively gold-plated with the Goldflash.   Tip: You can first gild parts very intensively and thickly with the Goldflash and then coat them briefly with the 8 or 12 gram cobalt-displaced hard gold!   2. bonding primer for the following coatings: Many applications require thin layers of gold before actual plating. Until now, this was only possible with the use of 24 carat gold and was therefore quite costly. cost-intensive. This is now a thing of the past.  With the Goldflash from Betzmann Galvanik, you can now apply the desired gold layer.   As an example, direct silver plating of nickel is usually not feasible, so you can first gold plate with the Goldflash, then silver plate. Likewise, when using black chrome, rose gold plating, green gold plating, the gold flash serves as an optimal bonding base when copper or nickel cannot be applied directly! Also, gilding nickel, which naturally oxidizes, is very easy and spotless. Then chrome plating on Goldflash can be done even easier and without problems.   Despite gold plating, the material input is far below 10 cents per cm2 of surface!   Recommended electrode: platinum electrode, graphite electrode Voltage: from approx. 4 volts    Procedure: Polishing if necessary Degreasing Activate Goldflash Continue with the top layer chrome, white gold, rose gold, green gold   Feature Used for Allows electroplating of a thin layer of strongly adherent gold. Before applying another layer of plating, for example when silver or palladium plating on stainless steel, nickel and its alloys. 24 carat thin coats of gold: electronics, optics – reflectors – and where the item is going to be protected with a clear lacquer layer.   Operating Conditions and Deposit Data Voltage Range 4.0 – 6.0 volts Temperature 14 – 25 °C Gold Concentration 2g/l Electrode Platinum or Carbon (see notes) Gold content in plate 99.9% (balance carbon) Plating Rate at (5.0 volts, Platinum electrode) Approx. 0.12 micron per minute (spot) Hardness 180 – 190 Hv Density of deposit 19.0 g/cm3 Stress Low – medium stress Special storage requirements Away from sunlight Shelf life Over 3 years Notes: We strongly advise against the use of stainless steel anodes for most of our plating processes Plating rates are calculated over a sample area which is permanently covered by swab.    Features Used for Designed mainly as a base solution for mixing with our Coloured Gold Mixers Mixing with Yellow, White, Rose, and Green Gold Mixers and Brass Effect Gold Mixer. Can be mixed with 2 or more Gold Mixers Creating a huge spectrum of different shades and tints of gold – good for exactly matching colour of original gold plated layer Can be plated on its own, forming a soft, 24 carat gold layer, completely cyanide free Mainly functional purposes only. Needs a Gold Flash undercoat if plating on to stainless steel       Signalword : Warning    H-phrases: H332 Harmful by inhalation. H312 Harmful in contact with skin. H302 Harmful if swallowed. P phrases: P280 Wear protective gloves/protective clothing/eye protection/face protection. P301 IF INFECTED:P310 Immediately call a POISON CENTER/doctor/  

Storage cup for the professional coating machine 50 Ampere Betzmann Galvanoshop:    This stable cup with screw cap fits perfectly into the holder of the professional electroplating unit. Capacity 300 ml. On request, you will receive the appropriate labelling for the material to be stored.   

Anode pad / tampon / anode sleeve / fuzzy sleeve / replacement fabric pad puffy from Betzmann Galvanik.    This puffy fabric pad / anode sleeve or also called tampon is absolutely recommended for all plating processes. Optimally suitable for all coatings and electrolytes.  The coating of larger areas is also quite fast with this pad.   The insertion hole is larger than the electrode and therefore it happens that the moist  anode pad slips off. Therefore, fix the pad on the electrode with a small rubber band.    

Anodenstoffpad  - Anodenhüllen dick mehrlagig - Ersatzhüllen für die Tampon Galvanik von Betzmann Real Gold   Dieser dicke Pads besteht aus mehreren zusammen genähten Lagen Stoff und eignet sich hervorragend für die Beschichtung größerer Flächen, aber auch für Teile mit Gittern wie z.B. einKühlergrill  usw. Am unteren Ende befinden sich 2 Einschublöcher für den Anodenstab. Falls dieser sich oben schon durch den Stoff gearbeitet hat, kann man den Pad durch Einstecken in das andereEinschubloch weiterhin benutzen. Bitte vor Anwendung den Pad gründlich durchnässen, sonst leitet er nicht.     Cotton Sleeve Big: This durable cotton anode Sleeves are custom designed to reach into tight recessed areas. Easy on, easy off, no rubber bands.     

Electrode Handle: The electrode handle is is used to hold the various electrodes up to 6mm required throughout the plating process.The Electrode Handle will hold all of our rod-shaped electrodes including the stainless steel electrode, which should be used for chrome stripping and cleaning only, the carbon electrode which can be used for plating all metals and the platinum electrode which can also be used for plating all metals.  

Connecting cable PLUS with banana plug:     Color RED  Length 1,50 meter For connection directly to the device      Color RED Length 1.50 meters For connection directly to the device incl. a stainless steel crocodile clip.     4mm banana plugs molded on both sides with strain relief and bend protection. Re-connectable - any number of plugs can be plugged into each other. Cylindrical contact spring for large area contact in the socket. Gold-plated contact surface for permanently low contact resistance. Fine stranded wire for highest flexibility and to avoid cable breakage. Conductor cross-section 1mm² - suitable for currents up to 25A. Double insulated cable with wear indicator by inner insulation in white -thereby damages at the insulation are immediately recognizable.   Pay attention to good quality for your electroplating and laboratory equipment! These cables have everything that is important for pleasant and durable use: large cross-section, good strain relief, gold-plated contacts and a flexible, yet resistant cable material with double insulation.